Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM10000000277T5
Model Year Start: 2023 Model: Corolla Prod Date Range: [09/2022 -           ]
Title: HYBRID / BATTERY CONTROL: INVERTER WITH CONVERTER: INSTALLATION; 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]

INSTALLATION

PROCEDURE

1. SET INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

(a) Temporarily install the inverter with converter assembly.

NOTICE:

  • When installing the inverter with converter assembly, be careful not to damage the parts around it.
  • To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.

    *a

    Correct

    *b

    Incorrect

2. CONNECT MOTOR CABLE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

(a) Temporarily connect the motor cable to the inverter with converter assembly with the 4 bolts.

NOTICE:

  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly during connection.

(b) Fully tighten the 3 bolts in the order shown in the illustration.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

*a

Waterproof Seal

*b

10 mm Union Nut Wrench Fulcrum Length

*c

Torque Wrench Fulcrum Length

(c) Using a 10 mm union nut wrench, fully tighten the bolt (A).

Torque:

Specified tightening torque :

8.0 N·m {82 kgf·cm, 6 ft·lbf}

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    7.0 N*m (71 kgf*cm, 62 in.*lbf)

(d) Temporarily install the 6 bolts.

CAUTION:

Insulate the tool with insulating tape.

NOTICE:

  • To prevent the threads from being damaged, temporarily tighten the 6 bolts by hand.
  • Do not damage the terminals, connector housing or inverter with converter assembly during connection.

(e) Fully tighten the 6 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

CAUTION:

Insulate the tool with insulating tape.

NOTICE:

  • Do not damage the terminals, connector housing or inverter with converter assembly during connection.
  • Be sure to use a torque wrench to tighten the bolts.

3. INSTALL INVERTER COVER

CAUTION:

Be sure to wear insulated gloves.

(a) To prevent the inverter with converter assembly from falling, temporarily install the bolt in the location shown in the illustration.

(b) Shift the position of the inverter with converter assembly and temporarily set it on top of the stud bolts as shown in the illustration.

NOTICE:

When lifting, make sure not to apply force to the motor cable.

(c) Install the inverter cover to the inverter with converter assembly with the 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

NOTICE:

  • Visually confirm that the inverter cover waterproof seal is securely installed before installing the inverter cover.
  • Do not touch the waterproof seal of the inverter cover.
  • Make sure that the interlock is fully engaged.
  • Do not damage the terminals, interlock connector or inverter with converter assembly during installation.
  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not remove or excessively tighten the screw of the inverter cover.

    *a

    Screw
  • Although the inverter cover may feel loose, this is not due to a malfunction.
  • Push in the inverter cover until it contacts the inverter with converter assembly.

    *a

    No Gap

(d) Shift the position of the inverter with converter assembly and temporarily set it on the hybrid vehicle transaxle assembly as shown in the illustration.

NOTICE:

When lifting, make sure not to apply force to the motor cable.

(e) Install the inverter cover with the bolt to the hybrid vehicle transaxle assembly.

Torque:

8.0 N·m {82 kgf·cm}

4. INSTALL INVERTER WITH CONVERTER ASSEMBLY

CAUTION:

Be sure to wear insulated gloves.

(a) Temporarily install the inverter with converter assembly with the 5 bolts and 2 nuts.

NOTICE:

  • When installing the inverter with converter assembly, be careful not to damage the parts around it.
  • To prevent damage, do not hold the inverter with converter assembly by the connectors, brackets or cooling pipes.
  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Make sure that the inverter with converter assembly is positioned so that the stud bolts are in contact with the base of the U-shaped portions of the No. 1 inverter bracket.

    *a

    Correct

    *b

    Incorrect

HINT:

If the bolts and nuts are not tightened appropriately, the inverter with converter assembly may make an abnormal noise.

(b) Fully tighten the 4 bolts in the order shown in the illustration.

Torque:

55 N·m {561 kgf·cm, 41 ft·lbf}

(c) Fully tighten the 2 nuts.

Torque:

55 N·m {561 kgf·cm, 41 ft·lbf}

5. CONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Engage the clamp and connect the engine wire to the inverter with converter assembly.

6. CONNECT INLET NO. 1 INVERTER COOLING HOSE

(a) Connect the inlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

  • To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
  • Make sure to align the alignment mark of the hose with the alignment mark of the pipe of the inverter with converter assembly.

HINT:

Make sure that the clip is positioned as shown in the illustration.

*a

Alignment Mark

*b

Rib

*c

2 to 11 mm (0.0787 to 0.4331 in.)

*d

Up

*e

LH Side

7. CONNECT OUTLET NO. 1 INVERTER COOLING HOSE

(a) Connect the outlet No. 1 inverter cooling hose to the inverter with converter assembly and slide the clip to secure it.

NOTICE:

  • To prevent foreign matter from entering the inverter with converter assembly and inverter cooling system, do not remove the pieces of cloth from the pipe and disconnected hose until installation.
  • Make sure to align the alignment mark of the hose with the rib of the inverter with converter assembly.

HINT:

Make sure that the clip is positioned as shown in the illustration.

*a

Alignment Mark

*b

Rib

*c

2 to 11 mm (0.0787 to 0.4331 in.)

*d

Up

*e

LH Side

8. CONNECT NO. 7 ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Engage the clamp.

(b) Connect the No. 7 engine wire to the inverter with converter assembly with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 89 in·lbf}

9. CONNECT NO. 3 ENGINE WIRE

(a) Engage the clamp.

(b) Engage the 2 claws to connect the engine wire to the No. 1 engine room relay block.

(c) Install the nut.

Torque:

8.35 N·m {85 kgf·cm, 74 in·lbf}

10. CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) for 4WD

Connect the HV floor under wire to the inverter with converter assembly and install the 2 bolts.

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.

(b) Engage the clamp.

(c) Connect the HV floor under wire to the inverter with converter assembly and install the 2 nuts and 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

NOTICE:

  • Do not allow any foreign matter or water to enter the inverter with converter assembly.
  • Do not touch the waterproof seal or terminals of the connector.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connector.

11. CONNECT ENGINE ROOM MAIN WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

(a) Connect the inverter with converter assembly connector.

(b) Engage the 3 clamps to connect the engine wire.

(c) Connect the inverter with converter assembly connector.

NOTICE:

  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.
  • Do not touch the waterproof seal or terminals of the connectors.

12. CONNECT ENGINE WIRE

CAUTION:

Be sure to wear insulated gloves.

NOTICE:

Do not allow any foreign matter or water to enter the inverter with converter assembly.

(a) Engage the 2 clamps to connect the engine wire.

(b) Engage the clamp.

(c) Install the 3 nuts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(d) Connect the inverter with converter assembly connector.

NOTICE:

  • To prevent damage due to static electricity, do not touch the terminals of the disconnected connectors.
  • Do not damage the terminals, connector housing or inverter with converter assembly when connecting the connectors.
  • Do not touch the waterproof seal or terminals of the connectors.

(e) Engage the 2 claws to connect the engine wire to the No. 1 engine room relay block.

(f) Connect the 2 No. 1 engine room relay block connectors.

(g) Install the No. 1 relay block cover to the No. 1 engine room relay block.

13. CONNECT HV AIR CONDITIONING WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Engage the 2 clamps.

*a

Green-colored Lock

Slide

(b) Connect the HV air conditioning wire connector and slide the green-colored lock as shown in the illustration to lock it securely.

NOTICE:

Make sure that the connectors are connected securely.

14. INSTALL NO. 1 AIR CLEANER INLET

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (INTAKE / EXHAUST): INTAKE MANIFOLD: INSTALLATION+

15. INSTALL AIR CLEANER BRACKET

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (INTAKE / EXHAUST): INTAKE MANIFOLD: INSTALLATION+

16. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (INTAKE / EXHAUST): INTAKE MANIFOLD: INSTALLATION+

17. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (INTAKE / EXHAUST): INTAKE MANIFOLD: INSTALLATION+

18. INSTALL NO. 2 AIR CLEANER INLET

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (INTAKE / EXHAUST): INTAKE MANIFOLD: INSTALLATION+

19. INSTALL RADIATOR SUPPORT OPENING COVER

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Sedan without Illumination): INSTALLATION+ 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; EXTERIOR PANELS / TRIM: FRONT BUMPER (for Sedan without Illumination): INSTALLATION+

20. INSTALL AIR CLEANER HOSE ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (ENGINE CONTROL): THROTTLE BODY: INSTALLATION+

21. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (ENGINE CONTROL): THROTTLE BODY: INSTALLATION+

22. CONNECT FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE

(a) Install the nut to connect the floor shift transmission control select cable.

Torque:

6.0 N·m {61 kgf·cm, 53 in·lbf}

23. INSTALL BATTERY CLAMP SUB-ASSEMBLY

(a) Install the battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:

15.4 N·m {157 kgf·cm, 11 ft·lbf}

24. INSTALL SERVICE PLUG GRIP

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: SERVICE PLUG GRIP: INSTALLATION

25. INSTALL ECM

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; 2ZR-FXE (ENGINE CONTROL): ECM: INSTALLATION

26. ADD COOLANT (for Inverter)

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; MAINTENANCE: COOLANT (for Inverter): REPLACEMENT+

27. INSPECT FOR COOLANT LEAK (for Inverter)

Click here 2020 - 2025 MY Corolla Corolla HV [01/2019 -        ]; HYBRID / BATTERY CONTROL: COOLANT (for Inverter): ON-VEHICLE INSPECTION+

28. PEFOME ECU CONFIGURATION

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: ECU CONFIGURATION

HINT:

Perform this procedure only when replacement of the inverter with converter assembly..

29. PERFORM RESOLVER LEARNING

Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10): UTILITY