Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM10000000277L4 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: WIPER / WASHER: WIPER AND WASHER SYSTEM (for Gasoline Model): Wiper and Washer Switch Circuit; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022] |
Wiper and Washer Switch Circuit
|
DESCRIPTION
The condition of the windshield wiper switch assembly is detected and sent to the steering sensor in this circuit.
WIRING DIAGRAM
for TMMMS Made:
for TMMMS Made:
for G16E-GTS:
for G16E-GTS:
except G16E-GTS:
except G16E-GTS:
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / Steering Angle Sensor / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > Steering Angle Sensor > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Wiper OFF Switch
|
Front wiper switch OFF position signal
|
OFF or ON
|
OFF: Front wiper switch not in OFF position
ON: Front wiper switch in OFF position
|
-
|
Wiper Auto/Int Switch
|
Front wiper switch INT position signal
|
OFF or ON
|
OFF: Front wiper switch not in INT position
ON: Front wiper switch in INT position
|
-
|
Wiper Lo Switch
|
Front wiper switch LO position signal
|
OFF or ON
|
OFF: Front wiper switch not in LO position
ON: Front wiper switch in LO position
|
-
|
Wiper Hi Switch
|
Front wiper switch HI position signal
|
OFF or ON
|
OFF: Front wiper switch not in HI position
ON: Front wiper switch in HI position
|
-
|
Wiper Mist Switch
|
Front wiper switch MIST position signal
|
OFF or ON
|
OFF: Front wiper switch not in MIST position
ON: Front wiper switch in MIST position
|
-
|
Washer Switch
|
Washer switch Fr WASH position signal
|
OFF or ON
|
OFF: Washer switch not in Fr WASH position
ON: Washer switch in Fr WASH position
|
-
|
Rear Wiper Lo Switch
|
Rear wiper switch Rr ON position signal
|
OFF or ON
|
OFF: Rear wiper switch not in Rr ON position
ON: Rear wiper switch in Rr ON position
|
*1
|
Rear Wiper Hi Switch
|
Rear wiper switch Rr INT position signal
|
OFF or ON
|
OFF: Rear wiper switch not in Rr INT position
ON: Rear wiper switch in Rr INT position
|
*1
|
Rear Washer Switch
|
Washer switch Rr WASH position signal
|
OFF or ON
|
OFF: Washer switch not in Rr WASH position
ON: Washer switch in Rr WASH position
|
*1
|
Intermittent Time Volume
|
Intermittent time adjustment switch condition
|
Shortest, Shorter, Longer or Longest
|
Shortest: P4
Shorter: P3
Longer: P2
Longest: P1
|
*2
|
-
*1: w/ Rear Wiper System
-
*2: Refer to Inspection for each position of the switch. (w/ Intermittent Time Adjustment Switch)
Click here
Chassis > Steering Angle Sensor > Data List
Tester Display
|
Wiper OFF Switch
|
Wiper Auto/Int Switch
|
Wiper Lo Switch
|
Wiper Hi Switch
|
Wiper Mist Switch
|
Washer Switch
|
Rear Wiper Lo Switch
|
Rear Wiper Hi Switch
|
Rear Washer Switch
|
Intermittent Time Volume
|
OK:
The Techstream display changes correctly in response to the windshield wiper switch assembly operation.
NG
|
|
|
2.
|
INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
|
(a) Remove the windshield wiper switch assembly.
Click here
(b) Inspect the windshield wiper switch assembly.
Click here
OK
|
|
|
3.
|
INSPECT STEERING WHEEL SWITCH HOUSING
|
(a) Remove the steering wheel switch housing.
Click here
(b) Inspect the steering wheel switch housing.
Click here
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (STEERING SENSOR - WINDSHIELD WIPER RELAY)
|
(a) Disconnect the A56 windshield wiper relay connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for TMMMS Made or G16E-GTS:
Tester Connection
|
Condition
|
Specified Condition
|
I46-2 (2S) - A56-3 (2S)
|
Always
|
Below 1 Ω
|
I46-2 (2S) or A56-3 (2S) - Body ground
|
Always
|
10 kΩ or higher
|
except TMMMS Made or G16E-GTS:
Tester Connection
|
Condition
|
Specified Condition
|
I211-2 (2S) - A56-3 (2S)
|
Always
|
Below 1 Ω
|
I211-2 (2S) or A56-3 (2S) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|