SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): B1820-B1823; Short in Side Squib (RH) Circuit; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM100000002779S
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): B1820-B1823; Short in Side Squib (RH) Circuit; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

DTC

B1820

Short in Side Squib (RH) Circuit

DTC

B1821

Open in Side Squib (RH) Circuit

DTC

B1822

Short in Side Squib (RH) Circuit (to Ground)

DTC

B1823

Short in Side Squib (RH) Circuit (to +B)

DESCRIPTION

The front side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH.

The airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib RH circuit.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	Warning Indicate	Test Mode / Check Mode
B1820	Short in Side Squib (RH) Circuit	The airbag sensor assembly detects a line short in the front side squib RH circuit during the primary check. Front side squib RH malfunction Airbag sensor assembly malfunction	Floor wire Front side squib RH (Front seat airbag assembly RH) Airbag sensor assembly	Comes on	Applies to check mode
B1821	Open in Side Squib (RH) Circuit	The airbag sensor assembly detects an open in the front side squib RH circuit. Front side squib RH malfunction Airbag sensor assembly malfunction	Floor wire Front side squib RH (Front seat airbag assembly RH) Airbag sensor assembly	Comes on	Applies to check mode
B1822	Short in Side Squib (RH) Circuit (to Ground)	The airbag sensor assembly detects a short to ground in the front side squib RH circuit. Front side squib RH malfunction Airbag sensor assembly malfunction	Floor wire Front side squib RH (Front seat airbag assembly RH) Airbag sensor assembly	Comes on	Applies to check mode
B1823	Short in Side Squib (RH) Circuit (to +B)	The airbag sensor assembly detects a short to B+ in the front side squib RH circuit. Front side squib RH malfunction Airbag sensor assembly malfunction	Floor wire Front side squib RH (Front seat airbag assembly RH) Airbag sensor assembly	Comes on	Applies to check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click here

HINT:

Perform the simulation method by selecting check mode (Signal Check) using the Techstream.
Click here
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.
Click here

PROCEDURE

1.	CHECK CONNECTORS

(a) Turn the ignition switch off.

*1	Front Seat Airbag Assembly RH
*2	Airbag Sensor Assembly
*3	Floor Wire

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

OK:

The connectors are properly connected.

HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the front seat airbag assembly RH and airbag sensor assembly.

(e) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

(f) Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.

REPLACE FLOOR WIRE

2.	CHECK FRONT SEAT AIRBAG ASSEMBLY RH

(a) Connect the connector to the airbag sensor assembly.

Front Seat Airbag Assembly RH

Airbag Sensor Assembly

Front view of wire harness connector

(to Front Seat Airbag Assembly RH)

(b) Connect SST (resistance 2.1 Ω) to connector C.

CAUTION:

Never connect a tester to the front seat airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:

Do not forcibly insert SST into the terminals of the connector when connecting it.
Insert SST straight into the terminals of the connector.

SST: 09843-18061

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

OK:

DTC B1820, B1821, B1822 or B1823 is not output.

HINT:

Codes other than DTCs B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(k) Disconnect SST from connector C.

REPLACE FRONT SEAT AIRBAG ASSEMBLY RH

3.	CHECK FLOOR WIRE

(a) Disconnect the floor wire from the airbag sensor assembly.

*1	Front Seat Airbag Assembly RH
*2	Airbag Sensor Assembly
*3	Floor Wire
*a	Front view of wire harness connector (to Front Seat Airbag Assembly RH)

(b) Check for a short to B+ in the circuit.

(1) Connect the cable to the negative (-) battery terminal.

(2) Turn the ignition switch to ON.

(3) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
Od1-1 (SFR+) - Body ground	Ignition switch ON	Below 1 V
Od1-2 (SFR-) - Body ground	Ignition switch ON	Below 1 V

(4) Turn the ignition switch off.

(5) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Od1-1 (SFR+) - Od1-2 (SFR-)	Always	Below 1 Ω

(d) Check for a short to ground in the circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Od1-1 (SFR+) - Body ground	Always	1 MΩ or higher
Od1-2 (SFR-) - Body ground	Always	1 MΩ or higher

(e) Check for a short in the circuit.

(1) Release the activation prevention mechanism built into connector B.

Click here

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
Od1-1 (SFR+) - Od1-2 (SFR-)	Always	1 MΩ or higher

(3) Restore the released activation prevention mechanism of connector B to the original condition.

REPLACE FLOOR WIRE

CHECK DTC

(a) Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.

*1	Front Seat Airbag Assembly RH
*2	Airbag Sensor Assembly

(b) Connect the cable to the negative (-) battery terminal.

(d) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

OK:

DTC B1820, B1821, B1822 or B1823 is not output.

HINT:

Codes other than DTCs B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.

USE SIMULATION METHOD TO CHECK

REPLACE AIRBAG SENSOR ASSEMBLY