Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000027775
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): B1637,B1638; Curtain Shield Airbag Sensor Lost Communication (LH); 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

DTC

B1637

Curtain Shield Airbag Sensor Lost Communication (LH)

DTC

B1638

Curtain Shield Airbag Sensor Initialization Error (LH)

DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the airbag sensor assembly, side airbag pressure sensor LH and side No. 2 airbag sensor LH.

The side airbag pressure sensor LH and side No. 2 airbag sensor LH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1637

Curtain Shield Airbag Sensor Lost Communication (LH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).
  • Side airbag pressure sensor LH malfunction
  • Side No. 2 airbag sensor LH malfunction
  • Airbag sensor assembly malfunction
  • Floor wire
  • Front door wire LH
  • Side airbag pressure sensor LH
  • Side No. 2 airbag sensor LH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

B1638

Curtain Shield Airbag Sensor Initialization Error (LH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).
  • Side airbag pressure sensor LH malfunction
  • Side No. 2 airbag sensor LH malfunction
  • Airbag sensor assembly malfunction
  • Floor wire
  • Front door wire LH
  • Side airbag pressure sensor LH
  • Side No. 2 airbag sensor LH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly, side airbag pressure sensor LH and side No. 2 airbag sensor LH. Also check that the connectors that link the floor wire and front door wire LH are properly connected.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

2.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag sensor assembly, side airbag pressure sensor LH and side No. 2 airbag sensor LH. Also disconnect the connectors that link the floor wire and front door wire LH.

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE FLOOR WIRE OR FRONT DOOR WIRE LH

OK

3.

CHECK FLOOR WIRE

(a) Connect the cable to the negative (-) battery terminal.

*1

Side No. 2 Airbag Sensor LH

*2

Airbag Sensor Assembly

*3

Floor Wire

*4

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Side No. 2 Airbag Sensor LH)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

O11-4 (BCL+) - Body ground

Ignition switch ON

Below 1 V

O11-3 (BCL-) - Body ground

Ignition switch ON

Below 1 V

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(f) Using a service wire, connect terminals 32 (BBL+) and 31 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O11-4 (BCL+) - O11-3 (BCL-)

Always

Below 1 Ω

(h) Disconnect the service wire from connector B.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O11-4 (BCL+) - O11-3 (BCL-)

Always

1 MΩ or higher

O11-4 (BCL+) - Body ground

Always

1 MΩ or higher

O11-3 (BCL-) - Body ground

Always

1 MΩ or higher

NG

REPLACE FLOOR WIRE

OK

4.

CHECK WIRE HARNESS

(a) Connect the connectors that link the floor wire and front door wire LH.

*1

Side Airbag Pressure Sensor LH

*2

Side No. 2 Airbag Sensor LH

*3

Front Door Wire LH

*4

Floor Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Side No. 2 Airbag Sensor LH)

*b

Front view of wire harness connector

(to Side Airbag Pressure Sensor LH)

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

O11-1 (BDL+) - Body ground

Ignition switch ON

Below 1 V

O11-2 (BDL-) - Body ground

Ignition switch ON

Below 1 V

(e) Turn the ignition switch off.

(f) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O11-1 (BDL+) - O11-2 (BDL-)

Always

Below 1 Ω

(i) Disconnect the service wire from connector E.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

O11-1 (BDL+) - O11-2 (BDL-)

Always

1 MΩ or higher

O11-1 (BDL+) - Body ground

Always

1 MΩ or higher

O11-2 (BDL-) - Body ground

Always

1 MΩ or higher

NG

GO TO STEP 7

OK

5.

CHECK SIDE NO. 2 AIRBAG SENSOR LH

(a) Connect the connectors to the side airbag pressure sensor LH and airbag sensor assembly.

*1

Side No. 2 Airbag Sensor RH

*2

Airbag Sensor Assembly

(b) Interchange the side No. 2 airbag sensor LH with RH and connect the connectors.

(c) Connect the cable to the negative (-) battery terminal.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

Result

Proceed to

DTC B1637 or B1638 is output.

A

DTC B1632 or B1633 is output.

B

DTCs B1632, B1633, B1637 and B1638 are not output.

C

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(k) Return the side No. 2 airbag sensor LH and RH to their original positions and connect the connectors.

B

REPLACE SIDE NO. 2 AIRBAG SENSOR LH

C

USE SIMULATION METHOD TO CHECK

A

6.

CHECK SIDE AIRBAG PRESSURE SENSOR LH

(a) Interchange the side airbag pressure sensor LH with RH and connect the connectors.

*1

Side Airbag Pressure Sensor RH

*2

Side No. 2 Airbag Sensor LH

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON, and wait for at least 60 seconds.

(d) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B1632, B1633, B1637 and B1638 may be output at this time, but they are not related to this check.

Result

Proceed to

DTC B1637 or B1638 is output.

A

DTC B1632 or B1633 is output.

B

DTCs B1632, B1633, B1637 and B1638 are not output.

C

(h) Turn the ignition switch off.

(i) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(j) Return the side airbag pressure sensor LH and RH to their original positions and connect the connectors.

A

REPLACE AIRBAG SENSOR ASSEMBLY

B

REPLACE SIDE AIRBAG PRESSURE SENSOR LH

C

USE SIMULATION METHOD TO CHECK

7.

CHECK FLOOR WIRE

(a) Disconnect the floor wire connector from the front door wire LH.

*1

Side Airbag Pressure Sensor LH

*2

Side No. 2 Airbag Sensor LH

*3

Front Door Wire LH

*4

Floor Wire

*5

Service Wire

*a

Front view of wire harness connector

(to Side No. 2 Airbag Sensor LH)

*b

Front view of wire harness connector

(to Front Door Wire LH)

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON.

(d) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

LO1-22 (BDL+) - Body ground

Ignition switch ON

Below 1 V

LO1-40 (BDL-) - Body ground

Ignition switch ON

Below 1 V

(e) Turn the ignition switch off.

(f) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(g) Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(h) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

LO1-22 (BDL+) - LO1-40 (BDL-)

Always

Below 1 Ω

(i) Disconnect the service wire from connector B.

(j) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

LO1-22 (BDL+) - LO1-40 (BDL-)

Always

1 MΩ or higher

LO1-22 (BDL+) - Body ground

Always

1 MΩ or higher

LO1-40 (BDL-) - Body ground

Always

1 MΩ or higher

OK

REPLACE FRONT DOOR WIRE LH

NG

REPLACE FLOOR WIRE