Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000276VL |
Model Year Start: 2023 |
Model: Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: P1607; Cruise Control Input Processor; 2023 MY Corolla [09/2022 - 11/2022] |
DTC
|
P1607
|
Cruise Control Input Processor
|
MONITOR DESCRIPTION
The ECM continuously monitors its main and sub CPUs. This self-check ensures that the ECM is functioning properly. If outputs from the CPUs are different and deviate from the standard, the ECM will illuminate the MIL and store this DTC.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P1607
|
Cruise Control Input Processor
|
ECM CPUs malfunction (1 trip detection logic).
|
ECM
|
Comes on
|
DTC stored
|
DTC for Mexico Models
- Applies
|
MONITOR STRATEGY
Related DTC
|
P1607: Internal control module performance
|
Required Sensors/Components (Main)
|
ECM
|
Required Sensors/Components (Related)
|
Cruise control
|
Frequency of Operation
|
Continuous
|
Duration
|
0.3 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
Both of the following conditions are met
|
-
|
Cruise control
|
Forbiddance
|
DMA communication error
|
Not detected
|
TYPICAL MALFUNCTION THRESHOLDS
Either of the following conditions is met
|
-
|
Cruise control
|
Operating
|
Low speed control
|
Operating
|
CONFIRMATION DRIVING PATTERN
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the Techstream off.
-
Turn the ignition switch off.
-
Disconnect the Techstream.
-
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
-
Connect the cable to the negative (-) battery terminal.
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Wait 16 seconds or more.
-
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
-
Input the DTC: P1607.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
N/A
|
-
Unable to perform DTC judgment
-
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
|
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs.
Click here
HINT:
-
If a permanent DTC is output, the system is malfunctioning.
-
If no permanent DTC is output, the system is normal.
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine and ECT > Clear DTCs
(e) Turn the ignition switch off.
NEXT
|
|
|
2.
|
READ OUTPUT DTC (DTC P1607)
|
(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
(b) Connect the cable to the negative (-) battery terminal.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Wait for 16 seconds or more.
(f) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(g) Read the DTCs.
Powertrain > Engine and ECT > Trouble Codes
Result
|
Proceed to
|
DTC is not output
|
A
|
DTC P1607 is output
|
B
|
|