Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000276LL |
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [09/2022 -
] |
Title: K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: P071512,P071514,P071531; Input/Turbine Speed Sensor "A" Circuit Short to Battery; 2023 - 2025 MY Corolla Corolla Hatchback [09/2022 - ] |
DTC
|
P071512
|
Input/Turbine Speed Sensor "A" Circuit Short to Battery
|
DTC
|
P071514
|
Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open
|
DTC
|
P071531
|
Input/Turbine Speed Sensor "A" No Signal
|
DESCRIPTION
The TCM uses signals from the transmission revolution sensor (NT) installed to the continuously variable transaxle to control the lock-up engagement pressure.
The transmission revolution sensor (NT) detects the input turbine speed and sends it to the TCM.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P071512
|
Input/Turbine Speed Sensor "A" Circuit Short to Battery
|
The transmission revolution sensor (NT) signal is normal but the transmission revolution sensor (NT) output voltage is higher than 1.8 V for 2 seconds or more (1-trip detection logic).
|
-
Wire harness or connector
-
Transmission revolution sensor (NT)
-
TCM
|
Comes on
|
DTC stored
|
SAE Code:
P07C0
|
P071514
|
Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open
|
The transmission revolution sensor (NT) signal is normal but the transmission revolution sensor (NT) output voltage is less than 0.2 V for 2 seconds or more (1-trip detection logic).
|
-
Wire harness or connector
-
Transmission revolution sensor (NT)
-
TCM
|
Comes on
|
DTC stored
|
SAE Code:
P07BF
|
P071531
|
Input/Turbine Speed Sensor "A" No Signal
|
When transmission revolution sensor (NSS) and (NOUT) signals both indicate 780 rpm or more, the transmission revolution sensor (NT) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic).
|
-
Wire harness or connector
-
Transmission revolution sensor (NT)
-
TCM
|
Comes on
|
DTC stored
|
SAE Code:
P0717
|
MONITOR DESCRIPTION
The transmission revolution sensor (NT) is used to detect the input turbine speed. The TCM determines the necessary gear ratio based on a comparison of the transmission revolution sensor (NT) (input turbine speed) and transmission revolution sensor (NOUT) (output shaft speed) signals.
When the output shaft speed is higher than the expected value and the input turbine speed is less than 300 rpm while driving with the shift lever in D, the TCM will determine that the transmission revolution sensor (NT) is malfunctioning, illuminate the MIL and store a DTC.
MONITOR STRATEGY
Related DTCs
|
P0717: Turbine speed sensor (Transmission revolution sensor (NT))/Verify pulse input
P07BF: Turbine speed sensor (Transmission revolution sensor (NT))/Range check (Low voltage)
P07C0: Turbine speed sensor (Transmission revolution sensor (NT))/Range check (High voltage)
|
Required sensors/Components
|
Transmission revolution sensor (NT)
Transmission revolution sensor (NSS)
Transmission revolution sensor (NOUT)
|
Frequency of operation
|
Continuous
|
Duration
|
P0717: 5 sec.
P07BF, P07C0: 2 sec.
|
MIL operation
|
Immediate
|
Sequence of operation
|
None
|
TYPICAL ENABLING CONDITIONS
All
Battery voltage
|
8 V or more
|
Engine switch
|
On (IG)
|
Starter
|
OFF
|
P0717
Turbine speed sensor range check fail (P07BF, P07C0)
(Pending / MIL)
|
Not detected
|
D range position switch
|
ON
|
R range position switch
|
OFF
|
Park position switch
|
OFF
|
Neutral position switch
|
OFF
|
Engine
|
Running
|
Pressure control solenoid circuit fail (P08CA, P08CB, P0962, P0963, P0966, P0967, P2826, P2827, P282F, P2830)
(Pending + MIL)
|
Not detected
|
Torque converter clutch pressure control solenoid circuit fail (P2763, P2764)
(Pending + MIL)
|
Not detected
|
Intermediate shaft speed sensor for belt drive revolution
|
780 rpm or more
|
Output speed sensor revolution
|
780 rpm or more
|
Vehicle speed sensor monitor condition judgment:
D range position switch
|
ON
|
R range position switch
|
OFF
|
Park position switch
|
OFF
|
Neutral position switch
|
OFF
|
Pressure control solenoid circuit fail (P08CA, P08CB, P0962, P0963, P0966, P0967, P2826, P2827, P282F, P2830)
(Pending + MIL)
|
Not detected
|
Torque converter clutch pressure control solenoid circuit fail (P2763, P2764)
(Pending + MIL)
|
Not detected
|
Output speed sensor revolution
|
380 rpm or more
|
Intermediate shaft speed sensor for belt drive revolution
|
380 rpm or more
|
One of the following conditions is met
|
-
|
- Speed sensor monitor driving mode
|
Belt mode (Synchronizer engaged)
|
- Speed sensor monitor driving mode
|
Belt mode (Synchronizer released)
|
One of the following conditions is met: Condition (A) or (B)
-
Condition (A)
ECT
|
20°C (68°F) or more
|
ECT sensor circuit fail (P0117, P0118)
(Pending + MIL)
|
Not detected
|
All of the following conditions are met
|
2 sec. or more
|
- Park position switch
|
OFF
|
- Neutral position switch
|
OFF
|
Condition (B)
One of the following conditions is met
|
-
|
- ECT
|
Less than 20°C (68°F)
|
- ECT sensor circuit fail (P0117, P0118)
(Pending + MIL)
|
Detected
|
All of the following conditions are met
|
30 sec. or more
|
- Park position switch
|
OFF
|
- Neutral position switch
|
OFF
|
P07BF, P07C0
Turbine speed sensor pulse input fail (P0717)
(Pending / MIL)
|
Not detected
|
TYPICAL MALFUNCTION THRESHOLDS
P0717
Turbine speed sensor revolution
|
Less than 300 rpm
|
P07BF
Turbine speed sensor voltage
|
Less than 0.2 V
|
P07C0
Turbine speed sensor voltage
|
More than 1.8 V
|
COMPONENT OPERATING RANGE
P0717
Turbine speed sensor revolution
|
300 rpm or more
|
P07BF, P07C0
Turbine speed sensor voltage
|
0.2 V or more and 1.8 V or less
|
CONFIRMATION DRIVING PATTERN
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
-
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
-
When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the engine switch on (IG) and turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the engine switch off and wait for 2 minutes or more.
-
Turn the engine switch on (IG) and turn the Techstream on.
-
Start the engine.
-
Perform the D Position Shift Test inspection in Road Test. [*1]
Click here
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
-
Stop the vehicle.
-
Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
-
Input the DTC: P071512, P071514 or P071531.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
N/A
|
-
Unable to perform DTC judgment
-
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
|
HINT:
-
If the judgment result shows NORMAL, the system is normal.
-
If the judgment result shows ABNORMAL, the system has a malfunction.
-
If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
for TMMMS Made
for TMC Made
CAUTION / NOTICE / HINT
CAUTION:
-
Strictly observe posted speed, limits, traffic laws and road conditions.
-
Do not drive the vehicle with the cable of the Techstream contacting the pedals, shift lever or steering wheel.
-
Driving the vehicle with the cable of the Techstream contacting these areas could impede vehicle control, resulting in a serious accident.
-
Do not operate the Techstream while driving the vehicle.
-
Operating the Techstream while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM (NT SENSOR SPEED AND NT SENSOR VOLTAGE)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Transmission / Data List.
(e) According to the display on the Techstream, read the Data List.
Powertrain > Transmission > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
NT Sensor Speed
|
Input turbine speed (NT)
|
Min.: 0 rpm
Max.: 65535 rpm
|
-
Equal to engine speed (NE): Lock-up ON (After warming up engine)
-
Nearly equal to engine speed (NE): Lock-up OFF (Engine idling with shift lever in P or N)
-
0 rpm: Vehicle stopped with shift lever in R
|
-
|
NT Sensor Voltage
|
Transmission revolution sensor (NT) output voltage
|
Min.: 0.000 V
Max.: 4.999 V
|
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N)
|
-
|
Powertrain > Transmission > Data List
Tester Display
|
NT Sensor Speed
|
NT Sensor Voltage
|
Result
|
Proceed to
|
Data List values are normal
|
A
|
Data List values are not normal
|
B
|
A
|
|
|
(a) Replace the TCM.
Click here
NEXT |
|
PERFORM REGISTRATION AND INITIALIZATION
for Registration: Click here
for Initialization: Click here
|
3.
|
INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
|
(a) Remove the transmission revolution sensor (NT).
Click here
(b) Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.
*1
|
Battery
|
*2
|
Ammeter
|
*a
|
Component without harness connected
(Transmission Revolution Sensor (NT))
|
*b
|
Magnet
|
*c
|
5 mm or less
|
-
|
-
|
(c) Wave a magnet left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NT) to output a high/low signal while measuring the current.
NOTICE:
Make sure to wave the magnet during the inspection. The current will not change unless the magnet is moved as shown in the illustration.
(d) Measure the current according to the value(s) in the table below.
Standard Current:
Tester Connection
|
Condition
|
Specified Condition
|
1 (NTO) - 2 (NTB)
|
Low signal
|
4 to 8 mA
|
1 (NTO) - 2 (NTB)
|
High signal
|
12 to 16 mA
|
OK
|
|
|
4.
|
CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NT) - TCM)
|
(a) for TMMMS Made:
(1) Disconnect the C67 transmission revolution sensor (NT) connector.
(b) for TMC Made:
(1) Disconnect the C112 transmission revolution sensor (NT) connector.
(c) Disconnect the C80 TCM connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance (for TMMMS Made):
Tester Connection
|
Condition
|
Specified Condition
|
C67-2 (NTB) - C80-25 (NTB)
|
Always
|
Below 1 Ω
|
C67-1 (NTO) - C80-9 (NTO)
|
Always
|
Below 1 Ω
|
C67-2 (NTB) or C80-25 (NTB) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C67-1 (NTO) or C80-9 (NTO) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
Standard Resistance (for TMC Made):
Tester Connection
|
Condition
|
Specified Condition
|
C112-2 (NTB) - C80-25 (NTB)
|
Always
|
Below 1 Ω
|
C112-1 (NTO) - C80-9 (NTO)
|
Always
|
Below 1 Ω
|
C112-2 (NTB) or C80-25 (NTB) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C112-1 (NTO) or C80-9 (NTO) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
(e) Connect the C80 TCM connector.
(f) for TMMMS Made:
(1) Connect the C67 transmission revolution sensor (NT) connector.
(g) for TMC Made:
(1) Connect the C112 transmission revolution sensor (NT) connector.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION REVOLUTION SENSOR (NOUT) - TCM)
|
OK
|
|
|
(a) Replace the TCM.
Click here
NEXT |
|
PERFORM REGISTRATION AND INITIALIZATION
for Registration: Click here
for Initialization: Click here
|
|