- Door window regulator assembly*
- Power window regulator motor sub-assembly
- Door glass*
- Door glass run*
- Door belt moulding*
- Door glass weatherstrip inner*
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000275UU |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR (for Rear Door): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
|
|
Initialize power window control system |
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
|
Initialize power window control system |
|
|
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)
Click here
3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)
Click here
4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS:
Click here
for 2ZR-FAE:
Click here
for 2ZR-FXE:
Click here
for G16E-GTS:
Click here
5. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Click here
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE REAR DOOR FRAME GARNISH
Click here
9. REMOVE REAR DOOR NO. 1 VENT SEAL
Click here
10. REMOVE REAR DOOR PANEL PROTECTOR
Click here
11. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
12. REMOVE REAR DOOR GLASS RUN
Click here
13. DISCONNECT REAR DOOR WEATHERSTRIP
Click here
14. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
16. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY
Click here
17. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY
|
(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly. |
|
|
|