- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000275OP |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: DOOR / HATCH: LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during luggage door lock control cable sub-assembly removal/installation are shown below.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
-
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for TMC Made:
Click here
for TMMMS Made:
Click here
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click here
for Power Seat:
Click here
2. REMOVE REAR SEAT ASSEMBLY
Click here
3. REMOVE REAR DOOR SCUFF PLATE LH (for Gasoline Model)
Click here
4. REMOVE REAR DOOR SCUFF PLATE LH (for HV Model)
Click here
5. REMOVE REAR UNDER SIDE COVER LH (for HV Model)
Click here
6. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
7. REMOVE REAR SEAT SIDE GARNISH LH (w/o Rear Seat Side Airbag)
Click here
8. REMOVE REAR SEAT SIDE GARNISH LH (w/ Rear Seat Side Airbag)
Click here
9. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
12. REMOVE LAP BELT OUTER ANCHOR COVER
Click here
13. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
14. REMOVE CENTER PILLAR LOWER GARNISH LH
Click here
15. REMOVE ROOF SIDE INNER GARNISH LH
Click here
16. REMOVE ROOF SIDE INNER GARNISH RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE CENTER STOP LIGHT SET
Click here
18. REMOVE PACKAGE TRAY TRIM BRACKET LH
Click here
19. REMOVE PACKAGE TRAY TRIM BRACKET RH
HINT:
Use the same procedure as for the LH side.
20. REMOVE REAR SEAT SHOULDER BELT HOLE COVER
Click here
21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
22. REMOVE LUGGAGE COMPARTMENT DOOR COVER
Click here
23. REMOVE SPARE WHEEL COVER
|
(a) Remove the spare wheel cover. |
|
24. REMOVE REAR FLOOR FINISH PLATE
|
(a) Remove the 2 clips. |
|
(b) Disengage the 2 clips, 2 claws and 6 guides to remove the rear floor finish plate as shown in the illustration.
|
Remove in this Direction |
25. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH
|
(a) Using a clip remover, remove the clip. |
|
(b) Using a clip remover, remove the clip (A), 5 clips (B) and luggage compartment trim cover assembly LH.
|
Clip (A) |
|
Clip (B) |
26. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
(a) Remove the screw. |
|
|
(b) Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration. |
|
|
(c) w/o Fuel Lid Opener Switch: (1) Disconnect the fuel lid lock control cable sub-assembly. |
|
(d) Disconnect the luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.
27. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY
(a) Turn back the floor carpet so that the luggage door lock control cable sub-assembly can be removed.
(b) w/o Wireless Door Lock System:
|
(1) Disconnect the luggage door lock control cable sub-assembly. |
|
(c) w/ Wireless Door Lock System:
|
(1) Disengage the claw as shown in the illustration. |
|
|
(2) Disconnect the luggage door lock control cable sub-assembly. |
|
|
(d) Disengage each clamp and disconnect the luggage door lock control cable sub-assembly. |
|
(e) Disengage each clamp and remove the luggage door lock control cable sub-assembly.
|
|