- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000275OK |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: DOOR / HATCH: FUEL LID LOCK CONTROL CABLE ASSEMBLY (for Hatchback): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during fuel lid lock control cable sub-assembly removal/installation are shown below.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
-
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
for TMC Made:
Click here
for TMMMS Made:
Click here
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat:
Click here
for Power Seat:
Click here
2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
3. REMOVE REAR FLOOR MAT ASSEMBLY (w/o Deck Board)
Click here
4. REMOVE REAR DECK TRIM COVER (w/o Deck Board)
Click here
5. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)
Click here
6. REMOVE SPARE WHEEL CUSHION (for GR)
Click here
7. REMOVE DECK FLOOR BOX LH (w/ Spare Tire)
Click here
8. REMOVE DECK FLOOR BOX RH (w/ Spare Tire)
Click here
9. REMOVE REAR NO. 1 FLOOR BOARD (w/ Spare Tire)
Click here
10. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)
Click here
11. REMOVE REAR DECK TRIM COVER (w/ Deck Board)
Click here
12. REMOVE REAR SEAT ASSEMBLY
Click here
13. REMOVE REAR DOOR SCUFF PLATE LH
Click here
14. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
15. REMOVE REAR SEAT SIDE GARNISH LH
Click here
16. REMOVE DECK TRIM SIDE LOWER BOARD LH (w/ Spare Tire)
Click here
17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
Click here
18. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
20. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
21. REMOVE LAP BELT OUTER ANCHOR COVER
Click here
22. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
Click here
23. REMOVE CENTER PILLAR LOWER GARNISH LH
Click here
24. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
|
(a) Remove the screw. |
|
|
(b) Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration. |
|
|
(c) Disconnect the fuel lid lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly. |
|
25. REMOVE FUEL FILLER OPENING LID LOCK RETAINER
|
(a) Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (A), and then pull the fuel filler opening lid lock retainer. |
|
|
(b) Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (B), and then pull the fuel filler opening lid lock retainer. |
|
|
(c) Pull out the fuel filler opening lid lock retainer with both the guides (B) and guides (C) aligned with the cutouts as shown in the illustration. |
|
(d) Disengage the 2 claws to remove the fuel filler opening lid lock retainer as shown in the illustration.
|
Remove in this Direction |
26. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
(a) Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.
(b) Disengage each clamp and remove the fuel lid lock control cable sub-assembly.
|
|