| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000275H7 |
| Model Year Start: 2023 | Model: Corolla Hatchback | Prod Date Range: [09/2022 - 03/2023] |
| Title: K120 / K121 (CVT): TRANSMISSION CONTROL CABLE (for TMMMS Made): INSTALLATION; 2023 MY Corolla Corolla Hatchback [09/2022 - 03/2023] | ||
INSTALLATION
PROCEDURE
1. INSTALL FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE
NOTICE:
Before installing the floor shift transmission control select cable, check that the shift lever is in N.
(a) Turn the transmission control shaft lever clockwise until it stops, then turn it counterclockwise 2 notches.
|
*a |
N |
NOTICE:
If the transmission control shaft lever is turned counterclockwise more than necessary, manual valve link lever sub-assembly may separate from the manual valve.
|
*1 |
Transmission Control Shaft Lever |
|
*a |
Manual Valve Link Lever Sub-assembly |
|
*b |
Manual Valve |
(b) Pass the floor shift transmission control select cable into the vehicle and install the floor shift transmission control select cable to the vehicle body with the 2 nuts.
Torque:
6.0 N·m {61 kgf·cm, 53 in·lbf}
(c) Connect the floor shift transmission control select cable to vehicle body with the nut.
Torque:
6.0 N·m {61 kgf·cm, 53 in·lbf}
(d) Connect the floor shift transmission control select cable to the No. 1 transmission control cable bracket with a new clip.
|
(e) Connect the floor shift transmission control select cable to the transmission control shaft lever as shown in the illustration. |
|
(f) Turn the nut of the floor shift transmission control select cable 180° counterclockwise. While holding the nut in place, push in the stopper until it clicks twice.
|
*a |
Stopper |
*b |
Nut |
|
*c |
Push in |
- |
- |
(g) Connect the floor shift transmission control select cable to the transmission floor shift assembly. Check that the spring is positioned at "A" and push in the stopper.
|
*1 |
Transmission Floor Shift Assembly |
- |
- |
|
*a |
Stopper |
*b |
Spring |
|
*c |
Nut |
*d |
Push in |
|
Connect in this Direction |
- |
- |
NOTICE:
- If the stopper cannot be pushed in, slightly turn the nut clockwise and then push in the stopper again.
- Make sure that the floor shift transmission control select cable is securely locked.
- Do not forcibly pull the floor shift transmission control select cable into the cabin.
(h) Connect the floor shift transmission control select cable to the transmission floor shift assembly.
|
|
Connect in this Direction |
NOTICE:
- Connect the floor shift transmission control select cable all the way to the base of the pin.
- Connect the floor shift transmission control select cable so that its adjustment lock section is on the driver side.
2. INSTALL CONSOLE BOX ASSEMBLY
Click here
![2023 MY Corolla Corolla Hatchback Corolla HV [09/2022 - 11/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (except G16E-GTS): INSTALLATION](/t3Portal/stylegraphics/info.gif)
3. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
(a) Install the front No. 1 floor heat insulator to the vehicle body with the 3 nuts.
Torque:
5.0 N·m {51 kgf·cm, 44 in·lbf}
4. INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
-
for Double Wishbone Type Suspension:
Click here
-
for Torsion Beam Type Suspension:
Click here
5. INSTALL FRONT FLOOR CENTER BRACE
Click here
6. INSTALL FRONT FLOOR COVER LH (w/ Cover)
Click here
7. INSTALL FRONT FLOOR COVER RH (w/ Cover)
Click here
8. INSTALL BATTERY CLAMP SUB-ASSEMBLY
Click here
9. INSTALL ECM
Click here
10. INSTALL BATTERY
Click here
11. INSPECT SHIFT LEVER POSITION
Click here
12. ADJUST SHIFT LEVER POSITION
Click here
13. INSPECT FOR EXHAUST GAS LEAK
-
for Double Wishbone Type Suspension:
Click here
-
for Torsion Beam Type Suspension:
Click here
|
|