Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000275GI |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: TIRE PRESSURE MONITORING: TIRE PRESSURE WARNING VALVE: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during tire pressure warning valve and transmitter removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure
|
Necessary Procedures
|
Effects/Inoperative when not Performed
|
Link
|
Tire pressure warning valve and transmitter
|
-
ID Registration
-
Initialization
-
Tire Position Identification
|
Tire Pressure Warning System
|
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replacement Part or Procedure
|
Necessary Procedures
|
Effects/Inoperative when not Performed
|
Link
|
for TMC Made
-
Tire pressure warning valve and transmitter
|
-
ID Registration
-
Initialization
-
Tire Position Identification
|
Tire Pressure Warning System
|
|
for TMMMS Made
-
Tire pressure warning valve and transmitter
|
-
Register transmitter ID
-
Initialize tire pressure warning system
|
-
When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates
-
Tire pressure warning function
|
for Registration
for Initialization
|
Tire
|
ECU Data Initialization (When performing tire replacement after RoB code X2104 is output)
|
Active Torque Split AWD System
|
|
PROCEDURE
1. REMOVE WHEEL ASSEMBLY
Click here
2. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type A)
(a) Remove the tire valve cap.
NOTICE:
Keep the removed tire valve cap.
(b) Remove the valve core to release the air from the tire.
NOTICE:
Make sure that a sufficient amount of air has been released.
(c) Using a tire remover, remove the tire from the disc wheel.
NOTICE:
-
Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.
-
Set the tire remover shoe as shown in the illustration.
|
|
*1
|
Tire
|
*a
|
Shoe
|
*b
|
10 to 20 mm (0.394 to 0.787 in.)
|
|
|
(d) Using a T10 "TORX" driver, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.
|
|
(e) Cut the tubeless tire valve and remove it by pulling from the outer side of the disc wheel as shown in the illustration.
*1
|
Tubeless Tire Valve
|
|
Cutting Area
|
3. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (for Type B)
(a) Remove the tire valve cap.
NOTICE:
Keep the removed tire valve cap.
(b) Remove the valve core to release the air from the tire.
NOTICE:
Make sure that a sufficient amount of air has been released.
(c) Using a 11 mm deep socket wrench, remove the nut and washer.
(d) Drop the tire pressure warning valve and transmitter with grommet into the tire.
HINT:
The grommet may remain attached to the rim.
(e) Using a tire remover, remove the tire from the disc wheel.
NOTICE:
-
Be careful not to damage the tire pressure warning valve and transmitter due to interference between the valve and the tire bead.
-
Set the tire remover shoe as shown in the illustration.
|
|
*1
|
Tire
|
*a
|
Shoe
|
*b
|
10 to 20 mm (0.394 to 0.787 in.)
|
|
|
(f) Take out the tire pressure warning valve and transmitter with grommet from the tire.
(g) Remove the grommet from the tire pressure warning valve and transmitter.
(h) Using a T10 "TORX" driver, remove the bolt and tire pressure monitor sensor from the tubeless tire valve.
|
|
|