Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000272EF |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Necessary Procedures
|
Link
|
Front Camera System (for TMC Made)
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Necessary Procedures
|
Link
|
Front Camera System (for TMC Made)
|
-
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
-
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
|
|
Pre-collision System (for TMMMS Made)
|
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
|
|
Lane Tracing Assist System (for TMMMS Made)
|
Lane Departure Alert System (for TMMMS Made)
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
|
Necessary Procedures
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)
Click here
3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)
Click here
4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for G16E-GTS: Click here
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
CAUTION:
for TMC Made:
-
Wait at least 60 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
for TMMMS Made:
-
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
5. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY (for Gasoline Model)
w/o Rear Seat Heater: Click here
6. REMOVE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
w/o Rear Seat Heater: Click here
7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
w/o Rear Seat Heater: Click here
8. REMOVE REAR SEAT ASSEMBLY (for Gasoline Model)
w/ Rear Seat Heater: Click here
9. REMOVE FRONT DOOR SCUFF PLATE
Click here
10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
(a) Disconnect the front door opening trim weatherstrip.
11. REMOVE REAR DOOR SCUFF PLATE (for Gasoline Model)
Click here
12. REMOVE REAR DOOR SCUFF PLATE (for HV Model)
Click here
13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
(a) Disconnect the rear door opening trim weatherstrip.
14. REMOVE LAP BELT OUTER ANCHOR COVER
(a) Disengage the 3 claws to remove the lap belt outer anchor cover.
|
|
15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY
(a) Remove the bolt to disconnect the floor anchor of the front seat outer belt assembly.
|
|
16. REMOVE CENTER PILLAR LOWER GARNISH
Click here
17. REMOVE CENTER PILLAR UPPER GARNISH
Click here
18. REMOVE FRONT SEAT OUTER BELT ASSEMBLY
(a) Remove the nut and disconnect the shoulder anchor of the front seat outer belt assembly.
|
|
(b) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.
HINT:
Tape the screwdriver tip before use.
|
|
*a
|
Protective Tape
|
*b
|
Locking Button
|
*c
|
Release
|
|
|
(d) Disengage the 2 guides to remove the front seat outer belt assembly.
19. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY
(b) Disengage the guide to remove the front shoulder belt anchor adjuster assembly.
|