- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000272ED |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: SEAT BELT: FRONT SEAT INNER BELT ASSEMBLY: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for TMC Made: Click here
![2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for TMMMS Made: Click here
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
Click here
2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
Click here
3. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
(a) for Manual Seat:
(1) Disconnect the connector.
|
(2) Disengage each clamp. |
|
(3) Remove the nut and front seat inner belt assembly.
(4) Remove the front seat belt anchor plate as shown in the illustration.
|
Remove in this Direction |
(b) for Power Seat:
(1) Disconnect the 2 connectors.
|
(2) Disengage each clamp. |
|
(3) Remove the nut and front seat inner belt assembly.
(4) Remove the front seat belt anchor plate as shown in the illustration.
|
|
Remove in this Direction |
4. REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
(a) Disconnect the connector.
|
(b) Disengage each clamp. |
|
(c) Remove the nut and front seat inner belt assembly.
(d) Remove the front seat belt anchor plate as shown in the illustration.
|
|
Remove in this Direction |
|
|