2ZR-FAE (ENGINE MECHANICAL): ENGINE UNIT: REMOVAL; 2023 MY Corolla [09/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM10000000271KT
Model Year Start: 2023	Model: Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: 2ZR-FAE (ENGINE MECHANICAL): ENGINE UNIT: REMOVAL; 2023 MY Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
1: w/ Smart Key System 2: w/o Smart Key System *3: w/ Steering Lock Function
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
	ECU communication ID registration (Immobiliser system)	Engine start function
	Reset memory Deceleration sensor zero point calibration CVT oil pressure calibration	Large shift shock Deterioration of fuel efficiency
Replacement of ECM*1	Code registration (Smart Key System (for Gasoline Model, Start Function))	Wireless Door Lock Control System (for Gasoline Model with Smart Key System) Smart Key System (for Gasoline Model, Entry Function) Smart Key System (for Gasoline Model, Start Function) Steering lock function*3
Replacement of ECM*2	Code registration (Immobiliser system)	Engine start Telematics System
Replacement of throttle body assembly Replacement of engine assembly Replacement of cylinder head sub-assembly Replacement of camshaft timing gear assembly Replacement of camshaft timing exhaust gear assembly Replacement of fuel injector assembly Replacement of spark plug Replacement of ignition coil assembly Gas leak from exhaust system is repaired Replacement of knock control sensor Replacement of engine coolant temperature sensor Replacement of continuously variable valve lift controller assembly	Inspection After Repair	Poor idle, etc. Engine start function, etc.
Front wheel alignment adjustment	Perform "Reset Memory". Perform acceleration sensor zero point calibration and store system information memorization.	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates	w/ Electric Parking Brake System: w/o Electric Parking Brake System:
CVT fluid	ATF thermal degradation estimate reset	The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly	for K313

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Pre-collision System (for TMMMS Made)	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)

PROCEDURE

1. REMOVE THROTTLE BODY ASSEMBLY

Click here

2. REMOVE INTAKE MANIFOLD

Click here

3. REMOVE PURGE VALVE (PURGE VSV)

*A	w/ Canister Pump Module
*B	w/o Canister Pump Module

(a) Remove the 2 bolts and purge valve (purge VSV) from the cylinder head cover sub-assembly.

4. DISCONNECT FUEL TUBE SUB-ASSEMBLY

Click here

5. REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Click here

6. REMOVE NO. 1 DELIVERY PIPE SPACER

Click here

7. REMOVE FUEL INJECTOR ASSEMBLY

Click here

8. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

(a) Remove the engine oil level dipstick.

(b) Remove the bolt and engine oil level dipstick guide.

9. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Click here

10. REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Click here

11. REMOVE MANIFOLD STAY

Click here

12. REMOVE EXHAUST MANIFOLD

Click here

13. REMOVE VENTILATION HOSE

Click here

14. DISCONNECT NO. 3 WATER BY-PASS HOSE

(a) Slide the clip and disconnect the No. 3 water by-pass hose from the water inlet housing

15. REMOVE NO. 1 WATER BY-PASS PIPE

(a) Remove the 2 bolts and No. 1 water by-pass pipe.

*A	for CVT
*B	for Manual Transaxle

16. REMOVE WATER BY-PASS HOSE

(a) Slide the clip and remove the water by-pass hose from the cylinder head sub-assembly.

17. REMOVE WATER INLET HOSE

(a) Slide the 2 clips and remove the water inlet hose.

18. SEPARATE WATER INLET

Click here

19. REMOVE THERMOSTAT

Click here

20. REMOVE VACUUM PUMP ASSEMBLY

Click here

21. REMOVE NO. 1 VACUUM PUMP BRACKET

(a) Remove the 2 bolts, No. 1 vacuum pump bracket and gasket.

22. REMOVE NO. 2 GENERATOR BRACKET

(a) Remove the bolt and No. 2 generator bracket from the cylinder head sub-assembly.

23. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:

Do not supply oil to the tensioner when an abnormal noise of the belt occurs.

(a) Remove the 2 bolts and V-ribbed belt tensioner assembly from the engine assembly.

24. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the bolt and wire harness clamp bracket from the cylinder head cover sub-assembly.

25. REMOVE IGNITION COIL ASSEMBLY

Click here

26. REMOVE ENGINE OIL TEMPERATURE SENSOR

Click here