Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000271KK
Model Year Start: 2023 Model: Corolla Prod Date Range: [09/2022 - 11/2022]
Title: 2ZR-FAE (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: REMOVAL; 2023 MY Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*1: w/ Smart Key System

*2: w/o Smart Key System

*3: w/ Steering Lock Function

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION

  1. Reset memory
  2. Deceleration sensor zero point calibration
  3. CVT oil pressure calibration
  • Large shift shock
  • Deterioration of fuel efficiency

2020 - 2023 MY Corolla Corolla Hatchback [01/2019 - 11/2022]; K313 (CVT): CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION

Replacement of ECM*1

Code registration (Smart Key System (for Gasoline Model, Start Function))
  • Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
  • Smart Key System (for Gasoline Model, Entry Function)
  • Smart Key System (for Gasoline Model, Start Function)
  • Steering lock function*3

2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, TMMMS Made)): REGISTRATION

Replacement of ECM*2

Code registration (Immobiliser system)
  • Engine start
  • Telematics System

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION

  • Replacement of engine assembly
  • Gas leak from exhaust system is repaired

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2020 - 2023 MY Corolla [01/2019 - 11/2022]; 2ZR-FAE (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Front wheel alignment adjustment
  1. Perform "Reset Memory".
  2. Perform acceleration sensor zero point calibration and store system information memorization.
  • VSC is disabled or malfunctions
  • DTCs are output
  • Slip indicator light illuminates
  • ABS warning light illuminates

w/ Electric Parking Brake System: 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System TMMMS Made): UTILITY

w/o Electric Parking Brake System: 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model without Electric Parking Brake System TMMMS Made): UTILITY

CVT fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly

2020 - 2023 MY Corolla Corolla Hatchback [01/2019 - 11/2022]; K313 (CVT): CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: INITIALIZATION for K313

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

Pre-collision System (for TMMMS Made)

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: PRE-COLLISION SYSTEM (for TMMMS Made): INITIALIZATION

Lane Tracing Assist System (for TMMMS Made)

Lane Departure Alert System (for TMMMS Made)

PROCEDURE

1. REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; K313 (CVT): CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY: REMOVAL

2. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Click here 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; CLUTCH: CLUTCH UNIT (for EC65): REMOVAL

3. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.
  • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
  • Using an engine sling device and engine lift, secure the engine assembly before servicing.

(b) Using SST, hold the crankshaft pulley.

SST: 09213-54015

91551-00850

SST: 09330-00021

(c) Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly and front drive plate spacer from the crankshaft.

4. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

(a) Using height adjustable attachments and plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, place the engine assembly horizontally.
  • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
  • Using an engine sling device and engine lift, secure the engine assembly before servicing.

(b) Using SST, hold the crankshaft pulley.

SST: 09213-54015

91551-00850

SST: 09330-00021

(c) Remove the 8 bolts and the flywheel sub-assembly from the crankshaft.

5. REMOVE REAR ENGINE OIL SEAL

(a) Using a knife, cut through the lip of the rear engine oil seal.

*a

Protective Tape

*b

Cut Position

(b) Using a screwdriver with its tip wrapped with protective tape, pry out the rear engine oil seal.

NOTICE:

Be careful not to damage the crankshaft.