Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000271KC
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System TMC Made): Steering Angle Sensor Wrong Installation (X0455); 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]

Steering Angle Sensor Wrong Installation (X0455)

DESCRIPTION

Code

Tester Display

Measurement Item

Trouble Area

X0455

Steering Angle Sensor Wrong Installation

History of steering angle sensor being installed incorrectly
  • Correct spiral cable with sensor sub-assembly
  • Steering angle sensor

CAUTION / NOTICE / HINT

NOTICE:

After performing the inspection, check and clear the vehicle control history (RoB).

HINT:

When Steering Angle Sensor Wrong Installation (X0455) is stored, engine output control may operate, but this is not a malfunction.

PROCEDURE

1.

CHECK FOR DTCs (HEALTH CHECK)

(a) Perform the Health Check using the GTS.

Result

Proceed to

DTCs are not output

A

DTCs are output

B
B

GO TO DIAGNOSTIC TROUBLE CODE CHART
A

2.

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
NEXT

3.

READ VALUE USING GTS (STEERING ANGLE SIGNAL INFORMATION)

(a) Check Data List item "steering angle signal information".

Chassis > Steering Angle Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Steering Angle Signal Information

Steering angle value (Rotation to the left side is positive)

Min.: -3072.0°

Max.: 3070.5°

Turning left: 0.0 to 3070.5°

Turning right: -3072.0 to 0.0°

During steering operation: Changes in proportion with steering wheel rotation

Chassis > Steering Angle Sensor > Data List

Tester Display

Steering Angle Signal Information

(b) Save the steering angle signal information to the GTS memory.

NOTICE:

  • If the value is +/- 360° (+/-15°), the steering angle sensor was incorrectly installed by 1 rotation.
  • If the value is +/- 720° (+/-15°), the steering angle sensor was incorrectly installed by 2 rotations.
  • In situations other than the above, the steering angle sensor may have been incorrectly installed by 3 or more rotations.

    In this case, it is possible that the proper installation or removal procedures were not followed, and the steering angle sensor may have been damaged.

Result

Proceed to

0 +/- 15°

A

+/- 360° (+/-15°) or +/- 720° (+/-15°)

B

None of the above conditions are met

C
B

GO TO STEP 7

C

GO TO STEP 13

A

4.

CLEAR VEHICLE CONTROL HISTORY (RoB)

(a) Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Tester Display

Vehicle Control History (RoB)
NEXT

5.

PERFORM ZERO POINT CALIBRATION OF STEERING ANGLE SENSOR

(a) Disconnect cable from negative (-) battery terminal.

HINT:

If the cable is not disconnected from the negative (-) battery terminal, it may not be possible to obtain an accurate steering angle sensor zero point.

(b) Connect cable to negative (-) battery terminal.

(c) Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.

NEXT

6.

CHECK VEHICLE CONTROL HISTORY (RoB)

(a) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

(b) Using the GTS, check for Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Tester Display

Vehicle Control History (RoB)

Result

Proceed to

X0455 is not output

A

X0455 is output

B
A

END
B

REPLACE STEERING ANGLE SENSOR

7.

ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

(a) Remove the spiral cable with sensor sub-assembly.

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: SPIRAL CABLE: REMOVAL

NOTICE:

  • Be sure to disconnect the cable from the negative (-) battery terminal before removing the spiral cable with sensor sub-assembly.

    HINT:

    If the cable is not disconnected from the negative (-) battery terminal, it may not be possible to obtain an accurate steering angle sensor zero point.

  • Do not disconnect the steering angle sensor from the spiral cable.

(b) Based on the steering angle signal information that was saved to the GTS memory earlier, rotate the spiral cable with sensor sub-assembly.

*A

w/o Heated Steering Wheel System

*B

w/ Heated Steering Wheel System

*C

Clockwise

*D

Counterclockwise

*a

Interlock

NOTICE:

  • Rotate the steering angle sensor without disconnecting it from the spiral cable.
  • Make sure to follow the adjustment method shown in the table.
  • Failure to observe the following precautions may result in damage to the spiral cable with sensor sub-assembly.
    • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock to release the interlock.
    • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.
    • Do not forcibly rotate the part.
    • Make sure to perform the correct number of rotations in the correct direction.

Steering Angle Signal Information

Correction Method

360° (+/-15°)

Rotate clockwise (to the right), 1 rotation.

- 360° (+/-15°)

Rotate counterclockwise (to the left), 1 rotation.

720° (+/-15°)

Rotate clockwise (to the right), 2 rotations.

- 720° (+/-15°)

Rotate counterclockwise (to the left), 2 rotations.

(c) Install the spiral cable with sensor sub-assembly.

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: SPIRAL CABLE: INSTALLATION

NEXT

8.

ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
NEXT

9.

READ VALUE USING GTS (STEERING ANGLE SIGNAL INFORMATION)

(a) Check Data List item "steering angle signal information".

Chassis > Steering Angle Sensor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Steering Angle Signal Information

Steering angle value

(Rotation to the left side is positive)

Min.: -3072.0°

Max.: 3070.5°

Turning left: 0.0 to 3070.5°

Turning right: -3072.0 to 0.0°

During steering operation: Changes in proportion with steering wheel rotation

Chassis > Steering Angle Sensor > Data List

Tester Display

Steering Angle Signal Information

Result

Proceed to

0 +/- 15°

A

None of the above conditions are met

B
B

REPLACE STEERING ANGLE SENSOR

A

10.

CLEAR VEHICLE CONTROL HISTORY (RoB)

(a) Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Tester Display

Vehicle Control History (RoB)
NEXT

11.

PERFORM ZERO POINT CALIBRATION OF STEERING ANGLE SENSOR

(a) Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.

NEXT

12.

CHECK VEHICLE CONTROL HISTORY (RoB)

(a) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

(b) Using the GTS, check for Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Tester Display

Vehicle Control History (RoB)

Result

Proceed to

X0455 is not output

A

X0455 is output

B
A

END
B

REPLACE STEERING ANGLE SENSOR

13.

CHECK STEERING WHEEL ASSEMBLY CENTER POSITION

(a) Perform steering wheel assembly center position adjustment.

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; STEERING COLUMN: STEERING SYSTEM: ADJUSTMENT

NEXT

14.

ADJUST WHEEL ALIGNMENT

for front wheel alignment: Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT

for rear wheel alignment (for Double Wishbone Type Suspension): Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ALIGNMENT / HANDLING DIAGNOSIS: REAR WHEEL ALIGNMENT (for Double Wishbone Type Suspension): ADJUSTMENT

for rear wheel alignment (for Torsion Beam Type Suspension): Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; ALIGNMENT / HANDLING DIAGNOSIS: REAR WHEEL ALIGNMENT (for Torsion Beam Type Suspension): INSPECTION

NEXT

15.

CLEAR VEHICLE CONTROL HISTORY (RoB)

(a) Using the GTS, clear the Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Tester Display

Vehicle Control History (RoB)
NEXT

16.

PERFORM STEERING SENSOR ZERO POINT CALIBRATION

(a) Disconnect cable from negative (-) battery terminal.

HINT:

If the cable is not disconnected from the negative (-) battery terminal, it may not be possible to obtain an accurate steering sensor zero point.

(b) Connect cable to negative (-) battery terminal.

(c) Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.

NEXT

17.

CHECK VEHICLE CONTROL HISTORY (RoB)

(a) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.

(b) Using the GTS, check for Vehicle Control History (RoB).

Chassis > Brake/EPB > Utility

Tester Display

Vehicle Control History (RoB)

Result

Proceed to

X0455 is not output

A

X0455 is output

B
A

END
B

REPLACE STEERING ANGLE SENSOR