| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000271IF |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model with Electric Parking Brake System TMC Made): Brake Hold Standby Indicator Light Circuit; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022] | ||
|
Brake Hold Standby Indicator Light Circuit |
DESCRIPTION
The brake hold standby indicator light turns on if brake hold control is possible when the following conditions required for operation standby are met and the brake hold switch (electric parking brake switch assembly) is pressed while the ignition switch is ON.
-
Conditions required for operation standby:
- The driver door is closed.
- The driver seat belt is fastened.
- The system is normal.
HINT:
If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.
- Brake system
- Electric parking brake system
WIRING DIAGRAM
PROCEDURE
|
1. |
PRE-CHECK |
(a) If the brake hold standby indicator light does not illuminate even though the brake hold switch (electric parking brake switch assembly) is pushed, check that the brake hold function operation conditions are met.
- The driver door is closed.
- The driver seat belt is fastened.
- The system is normal.
HINT:
If a malfunction occurs in one of the following systems, the brake hold operated indicator light will blink. If this occurs, perform troubleshooting on the malfunctioning system.
- Brake system
- Electric parking brake system
|
|
2. |
READ VALUE USING GTS (BRAKE HOLD READY) |
(a) Connect the GTS to the DLC3.
(b) Turn the ignition switch to ON.
(c) Enter the following menus: Chassis / Brake/EPB / Data List.
Chassis > Brake > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Brake Hold Ready |
Brake hold control permission status |
Not in stand-by mode / Stand-by mode |
Not in stand-by mode: Brake hold function not operating (brake hold standby indicator light not illuminated) Stand-by mode: Brake hold function stand-by state (brake hold standby indicator light illuminated) |
- |
Chassis > Brake > Data List
|
Tester Display |
|---|
|
Brake Hold Ready |
(d) All of the following brake hold operation conditions are met:
- The driver door is closed.
- The driver seat belt is fastened.
(e) Check the brake hold standby indicator light and mode condition on the GTS changes according to brake hold switch (electric parking brake switch assembly) operation.
Standard:
|
Brake Hold Switch (Electric Parking Brake Switch Assembly) Operation |
Mode Condition Display |
Brake Hold Standby Indicator Light |
|---|---|---|
|
Not pressed |
Not in stand-by mode |
Does not come on |
|
Pressing the brake hold switch (electric parking brake switch assembly) |
Stand-by mode |
come on |
|
Result |
Proceed to |
|---|---|
|
Indicator light and mode condition display do not change |
A |
|
Mode condition display is normal, but indicator light does not change |
B |
|
Indicator light and mode condition display are normal |
C |
| B |
|
INSPECT METER / GAUGE SYSTEM except 12.3 Inch Display: Click here
for 12.3 Inch Display: Click here
|
![2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM (except 12.3 Inch Display): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
| C |
|
|
|
3. |
INSPECT ELECTRIC PARKING BRAKE SWITCH ASSEMBLY |
|
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector. OK: The connector is securely connected. |
|
(b) Disconnect the I159 brake hold switch (electric parking brake switch assembly) connector.
(c) Check both the connector case and the terminal for deformation and corrosion.
OK:
No deformation or corrosion.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
10 (+B) - 12 (E) |
Switch pushed |
Below 50 Ω |
|
10 (+B) - 12 (E) |
Switch not pushed |
10 kΩ or higher |
| NG |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY) |
(a) Make sure that there is no looseness at the locking part and the connecting part of the connector.
OK:
The connector is securely connected.
(b) Disconnect the A51 skid control ECU (brake actuator assembly) connector.
(c) Disconnect the I159 brake hold switch (electric parking brake switch assembly) connector.
(d) Check both the connector case and the terminal for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
I159-10 (+B) - A51-42 (HZRI) |
Always |
Below 1 Ω |
|
I159-10 (+B) or A51-42 (HZRI) - Body ground |
Always |
10 kΩ or higher |
|
I159-12 (E) - Body ground |
1 minute or more after disconnecting the cable from the negative (-) battery terminal |
Below 1 Ω |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|