- Sliding roof ECU(sliding roof drive gear sub-assembly)*1
- Sliding roof glass sub-assembly*1
- Sliding roof drive cable sub-assembly*1
- Sliding roof housing sub-assembly*1
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000271AR |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF HOUSING: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof housing removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
| *1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
|
|
Initialize sliding roof system |
|
|
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
| *1: Even when not replacing the part, it is necessary to perform the specified necessary procedures after installation. | |||
|
Initialize sliding roof system |
|
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for TMC Made: Click here
![2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for TMMMS Made: Click here
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
PROCEDURE
1. REMOVE SLIDING ROOF SIDE GARNISH LH
|
(a) Disengage the 4 claws to remove the sliding roof side garnish LH. |
|
2. REMOVE SLIDING ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
3. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY
(a) Move the sliding roof glass sub-assembly to the fully closed position.
(b) Using a T25 "TORX" socket wrench, remove the 4 screws and sliding roof glass sub-assembly.
NOTICE:
To prevent the sliding roof glass sub-assembly and sliding roof drive gear sub-assembly from becoming misaligned, move the sliding roof glass sub-assembly (sliding roof drive cable sub-assembly) to the fully closed position before removing it.
4. REMOVE SLIDING ROOF WEATHERSTRIP
|
(a) Remove the sliding roof weatherstrip from the sliding roof panel sub-assembly. |
|
5. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH
Click here
6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
7. DISCONNECT SLIDING ROOF DRAIN HOSE
HINT:
Use the same procedure for all of the sliding roof drain hoses.
|
(a) Disengage the claw and disconnect the sliding roof drain hose. |
|
8. REMOVE SLIDING ROOF OR REMOVABLE ROOF HOUSING SUB-ASSEMBLY
(a) Remove the 8 bolts, 6 nuts and sliding roof or removable roof housing sub-assembly.
|
|