|
Last Modified: 01-27-2025 |
6.11:8.1.0 |
Doc ID: RM100000002718Q |
|
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [09/2022 - 11/2022] |
|
Title: K313 (CVT): PARK / NEUTRAL POSITION SWITCH: REMOVAL; 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during park/neutral position switch assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replacement Part or Procedure
|
Necessary Procedure
|
Effect/Inoperative when not Performed
|
Link
|
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
-
Reset memory
-
Deceleration sensor zero point calibration
-
CVT oil pressure calibration
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
|
|
Replacement of ECM*1
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function*3
|
|
|
Replacement of ECM*2
|
Code registration (Immobiliser system)
|
Engine start
|
|
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
|
Pre-collision System (for TMMMS Made)
|
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
|
|
|
Lane Tracing Assist System (for TMMMS Made)
|
|
Lane Departure Alert System (for TMMMS Made)
|
PROCEDURE
1. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
-
Make sure to apply the parking brake and chock a wheel before performing this procedure.
-
If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click here
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
4. REMOVE RADIATOR SUPPORT OPENING COVER
Click here
5. REMOVE INLET NO. 1 AIR CLEANER
Click here
6. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
7. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
8. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here
9. REMOVE ECM
Click here
10. REMOVE BATTERY
Click here
11. DISCONNECT ENGINE WIRE
|
(a) Remove the bolt and nut to disconnect the engine wire from the battery clamp sub-assembly.
|
|
12. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
13. DISCONNECT FLOOR SHIFT TRANSMISSION CONTROL SELECT CABLE
(a) Move the shift lever to N.
|
(b) Remove the nut and disconnect the floor shift transmission control select cable from the control shaft lever.
|
|
(c) Remove the clip and disconnect the floor shift transmission control select cable from the No. 1 transmission control cable bracket.
14. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
|
(a) Disconnect the park/neutral position switch assembly connector.
|
|
(b) Remove the nut, washer and control shaft lever from the park/neutral position switch assembly.
|
(c) Using a screwdriver, bend back the tabs of the lock plate.
|
|
(d) Remove the lock nut and lock plate from the park/neutral position switch assembly.
|
(e) Remove the 2 bolts and park/neutral position switch assembly from the continuously variable transaxle assembly.
|
|
|