THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022

Last Modified: 07-31-2024	6.11:8.1.0	Doc ID: RM1000000027189
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: THEFT DETERRENT / KEYLESS ENTRY: CERTIFICATION ECU: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during certification ECU (smart key ECU assembly) removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: w/ Smart Key System

Certification ECU (smart key ECU assembly)*

Code registration (Smart Key System (for Gasoline Model, Start Function))

Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
Smart Key System (for Gasoline Model, Entry Function)
Smart Key System (for Gasoline Model, Start Function)
Steering lock function

for TMC Made

for TMMMS Made

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
1: for GR Model 2: except GR Model
Front Camera System (for TMC Made)	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.1 Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.2
Pre-collision System (for TMMMS Made)	Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
*1: for Hatchback
Power Door Lock Control System Back door opener*1	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Certification ECU (smart key ECU assembly)	Code registration (Smart Key System (for Start Function, HV Model))	Wireless Door Lock Control System (for HV Model) Smart Key System (for Entry Function, HV Model) Smart Key System (for Start Function, HV Model)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))

HINT:

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed	Necessary Procedure	Link
Front Camera System (for TMC Made)	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

PROCEDURE

1. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

2. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Click here

3. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click here

5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Click here

6. REMOVE NO. 2 INSTRUMENT SIDE PANEL

Click here

7. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

Click here

8. REMOVE AIR CONDITIONING CONTROL ASSEMBLY

Click here

9. REMOVE CENTER INSTRUMENT PANEL REGISTER ASSEMBLY

Click here

10. REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY

Click here

11. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Click here

12. REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

Click here

13. REMOVE ECU INTEGRATION BOX RH

for TMC Made: Click here

for TMMMS Made: Click here

14. REMOVE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Disengage the 2 claws and remove the certification ECU (smart key ECU assembly) as shown in the illustration.

NOTICE:

If the ECU integration box RH is deformed or damaged, replace it.
Do not bend the 2 claws more than necessary.

Remove in this Direction