Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM100000002714E |
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [09/2022 - 11/2022] |
Title: EG60 (MANUAL TRANSMISSION / TRANSAXLE): TRANSMISSION CONTROL CABLE (except TMC Made): REMOVAL; 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
|
Gas leak from exhaust system is repaired
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
Replacement of ECM*1
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function*3
|
|
Replacement of ECM*2
|
Code registration (Immobiliser system)
|
-
Engine start
-
Telematics System
|
|
CAUTION:
-
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
-
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Pre-collision System (for TMMMS Made)
|
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
|
|
Lane Tracing Assist System (for TMMMS Made)
|
Lane Departure Alert System (for TMMMS Made)
|
PROCEDURE
1. SECURE VEHICLE
(a) Fully apply the parking brake and chock a wheel.
CAUTION:
-
Make sure to apply the parking brake and chock a wheel before performing this procedure.
-
If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
2. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click here
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
4. REMOVE BATTERY
Click here
5. REMOVE CONSOLE BOX ASSEMBLY
Click here
6. REMOVE RADIATOR SUPPORT OPENING COVER
Click here
7. REMOVE INLET NO. 1 AIR CLEANER
Click here
8. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
9. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
10. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
Click here
11. REMOVE ECM
Click here
12. REMOVE BATTERY CLAMP SUB-ASSEMBLY
Click here
13. REMOVE FRONT FLOOR COVER LH (w/ Cover)
Click here
14. REMOVE FRONT FLOOR COVER RH (w/ Cover)
Click here
15. REMOVE FRONT FLOOR CENTER BRACE
Click here
16. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)
Click here
17. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
(a) Remove the 3 nuts and front No. 1 floor heat insulator from the vehicle body.
|
|
18. REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.
|
|
*a
|
Transmission Control Select Cable
|
*b
|
Transmission Control Shift Cable
|
|
|
(b) Disconnect the transmission control shift cable from the floor shift shift lever assembly.
(c) Using a screwdriver, pull out the stopper of the transmission control select cable.
NOTICE:
Do not remove the stopper. If it is removed, reinstall it to its original position.
|
|
(d) Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control select cable from the floor shift shift lever assembly.
NOTICE:
-
Do not rotate the nut excessively as the internal spring may jump out and the transmission control cable assembly will not be reusable.
-
Do not forcibly pull the transmission control cable assembly into the cabin.
|
|
(e) Disconnect the transmission control shift cable from the floor shift shift lever assembly in the same manner as the transmission control select cable.
(f) Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.
|
|
(g) Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.
(i) Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.
(j) Remove the 2 nuts and transmission control cable assembly from the vehicle body.
|
|
|