Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000027147 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: THEFT DETERRENT / KEYLESS ENTRY: ELECTRICAL KEY OSCILLATOR (for Hatchback Inside Luggage Compartment): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during No. 3 indoor electrical key antenna assembly removal/installation are shown below.
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
-
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Front Camera System (for TMC Made)
|
-
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
-
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
|
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for M20A-FKS: Click here
for G16E-GTS: Click here
3. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
4. REMOVE REAR FLOOR MAT ASSEMBLY (w/o Deck Board)
Click here
5. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)
Click here
6. REMOVE REAR NO. 1 FLOOR BOARD (w/ Spare Tire)
Click here
7. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)
Click here
8. REMOVE SPARE WHEEL CUSHION (for GR)
Click here
9. REMOVE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (except GR)
(a) Disconnect the connector.
|
|
(b) Disengage the clamp to remove the No. 3 indoor electrical key antenna assembly.
NOTICE:
Be careful when removing the No. 3 indoor electrical key antenna assembly. If the No. 3 indoor electrical key antenna assembly is dropped, replace it with a new one.
10. REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (for GR)
(a) Disconnect the connector.
|
|
(b) Disengage the clamp to remove the No. 2 indoor electrical key antenna assembly.
NOTICE:
Be careful when removing the No. 2 indoor electrical key antenna assembly. If the No. 2 indoor electrical key antenna assembly is dropped, replace it with a new one.
|