Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000270U1
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: CLUTCH: CLUTCH PEDAL: REMOVAL; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during clutch pedal sub-assembly removal/installation are shown below.

CAUTION:

Be sure to read Precaution thoroughly before servicing.

  • for TMC Made Gasoline Model:

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION

  • for TMMMS Made:

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): PRECAUTION

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: for GR Model

*2: except GR Model

Front Camera System (for TMC Made)

  • Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
  • Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more.*2

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM (for TMC Made): INITIALIZATION

Pre-collision System (for TMMMS Made)

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: PRE-COLLISION SYSTEM (for TMMMS Made): INITIALIZATION

Lane Tracing Assist System (for TMMMS Made)

Lane Departure Alert System (for TMMMS Made)

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedure

Link

*1: for Hatchback

Power Door Lock Control System

  • Back door opener*1

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for TMC Made): INITIALIZATION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

2. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL

3. DISCONNECT CLUTCH MASTER CYLINDER ASSEMBLY

(a) Remove the clip from the clevis pin.

*A

for Hatchback

*B

for Sedan

(b) Remove the clevis pin to disconnect the clutch master cylinder assembly from the clutch pedal sub-assembly.

4. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY (w/ Clutch Pedal Stroke Sensor Assembly)

(a) Disconnect the clutch pedal stroke sensor assembly connector.

*a

Clutch Pedal Stroke Sensor Assembly Connector

*b

Clutch Switch Start Assembly Connector

(b) Disconnect the clutch start switch assembly connector.

(c) Disengage the clamp to disconnect the wire harness from the clutch pedal support assembly.

(d) Remove the 2 bolts and No. 4 instrument panel bracket from the clutch pedal support assembly and instrument panel reinforcement assembly.

(e) Remove the 2 nuts and clutch pedal support assembly from the vehicle body.

(f) Remove the clip nut from the clutch pedal bracket sub-assembly.

5. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY (w/o Clutch Pedal Stroke Sensor Assembly)

(a) Disconnect the clutch switch assembly connector.

*a

Clutch Switch Assembly Connector

*b

Clutch Start Switch Assembly Connector

(b) Disconnect the clutch start switch assembly connector.

(c) Disengage the 2 clamps to disconnect the wire harness from the clutch pedal support assembly.

(d) Remove the 2 bolts and No. 4 instrument panel bracket from the clutch pedal support assembly and instrument panel reinforcement assembly.

(e) Remove the 2 nuts and clutch pedal support assembly from the vehicle body.

(f) Remove the clip nut from the clutch pedal bracket sub-assembly.

6. REMOVE CLUTCH SWITCH ASSEMBLY (w/o Clutch Pedal Stroke Sensor Assembly)

Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; CLUTCH: CLUTCH PEDAL SWITCH: REMOVAL+

7. REMOVE CLUTCH START SWITCH ASSEMBLY

Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; CLUTCH: CLUTCH PEDAL SWITCH: REMOVAL+

8. REMOVE CLUTCH PEDAL STROKE SENSOR ASSEMBLY (w/ Clutch Pedal Stroke Sensor Assembly)

Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; CLUTCH: CLUTCH STROKE SENSOR: REMOVAL+

9. REMOVE CLUTCH PEDAL SPRING

(a) Move the clutch pedal sub-assembly to the full stroke position.

*A

w/ Clutch Pedal Stroke Sensor Assembly

*B

w/o Clutch Pedal Stroke Sensor Assembly

(b) Remove the clutch pedal spring from the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.

10. REMOVE CLUTCH PEDAL SUB-ASSEMBLY

(a) Mount the clutch pedal sub-assembly in a soft jaw vise.

NOTICE:

Be careful not to damage the clutch pedal sub-assembly in the vise.

(b) Remove the bolt, nut, clutch pedal sub-assembly and clutch pedal bracket sub-assembly from the clutch pedal support sub-assembly.

*A

w/ Clutch Pedal Stroke Sensor Assembly

*B

w/o Clutch Pedal Stroke Sensor Assembly

*1

Clutch Pedal Bracket Sub-assembly

*2

Clutch Pedal Sub-assembly

11. REMOVE CLUTCH PEDAL SPRING HOLDER

(a) Remove the clutch pedal spring holder from the clutch pedal bracket sub-assembly.

12. REMOVE CLUTCH PEDAL TURNOVER BUSHING

(a) Remove the clutch pedal turnover bushing from the clutch pedal sub-assembly.

*A

w/ Clutch Pedal Stroke Sensor Assembly

*B

w/o Clutch Pedal Stroke Sensor Assembly

13. REMOVE CLUTCH PEDAL SHAFT COLLAR

(a) Remove the 2 clutch pedal bushings and clutch pedal shaft collar from the clutch pedal sub-assembly.

*A

w/ Clutch Pedal Stroke Sensor Assembly

*B

w/o Clutch Pedal Stroke Sensor Assembly

14. REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

(a) Using SST and a hammer, remove the clutch master cylinder push rod clevis bushing from the clutch pedal sub-assembly.

SST: 09201-01055

SST: 09950-70010

09951-07100

*A

w/ Clutch Pedal Stroke Sensor Assembly

*B

w/o Clutch Pedal Stroke Sensor Assembly

*1

Clutch Master Cylinder Push Rod Clevis Bushing

15. REMOVE CLUTCH PEDAL PAD

(a) Remove the clutch pedal pad from the clutch pedal sub-assembly.