- Poor idle, etc.
- Engine start function, etc.
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM10000000270OK |
| Model Year Start: 2023 | Model: Corolla Hatchback | Prod Date Range: [09/2022 - 11/2022] |
| Title: M20A-FKS (STARTING): STARTER: REMOVAL; 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during starter assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Gas leaks from exhaust system is repaired |
Inspection after repair |
|
|
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
|
Front Camera System (for TMC Made) |
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more. |
|
|
Pre-collision System (for TMMMS Made) |
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. |
|
|
Lane Tracing Assist System (for TMMMS Made) |
||
|
Lane Departure Alert System (for TMMMS Made) |
Learning completes when vehicle is operated normally
|
Effect/Inoperative Function when Necessary Procedure not Performed |
Necessary Procedure |
Link |
|---|---|---|
| *1: for Hatchback | ||
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. |
|
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here
4. REMOVE INTAKE MANIFOLD
Click here
5. REMOVE FLYWHEEL HOUSING SIDE COVER
|
(a) Disengage the claw as shown in the illustration to remove the flywheel housing side cover. |
|
6. REMOVE STARTER ASSEMBLY
|
(a) Disconnect the starter assembly connector. |
|
|
(b) Disengage the claw and remove the starter assembly cover (cover B) from the starter assembly cover (base) and starter assembly cover (cover A). |
|
|
(c) Remove the nut to disconnect the engine wire from terminal 30. |
|
|
(d) Remove the bolt and disconnect the engine wire. |
|
|
(e) Remove the 2 bolts and starter assembly. |
|
|
(f) Remove the starter assembly cover (cover A) from the starter assembly cover (base). |
|
|
(g) Remove the nut and starter terminal from the starter assembly. |
|
|
(h) Disengage the 2 claws and remove the starter terminal from the starter assembly cover (base). |
|
|
|