- Door glass*1
- Door glass run*1
- Door belt moulding*1
- Door glass weatherstrip inner*1
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM10000000270MC |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Rear Door): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation. | |||
|
|
Initialize power window control system |
|
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System
- Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power Door Lock Control System
- Back door opener
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. REMOVE DECK BOARD ASSEMBLY
Click here
3. REMOVE SPARE WHEEL CUSHION
Click here
4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click here
5. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
Click here
6. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL
Click here
7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY
Click here
8. REMOVE REAR SPEAKER ASSEMBLY
Click here
9. REMOVE REAR DOOR FRAME GARNISH
Click here
10. REMOVE REAR DOOR NO. 1 VENT SEAL
Click here
11. REMOVE REAR DOOR PANEL PROTECTOR
Click here
12. REMOVE REAR DOOR SERVICE HOLE COVER
Click here
13. REMOVE REAR DOOR GLASS RUN
Click here
14. DISCONNECT REAR DOOR WEATHERSTRIP
Click here
15. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY
Click here
16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY
Click here
17. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP WITH REAR DOOR QUARTER WINDOW GLASS
Click here
18. REMOVE REAR DOOR OUTSIDE STRIPE
HINT:
When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Rear Door Outside Stripe and Vehicle Body |
40 to 60°C (104 to 140°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the rear door outside stripe and vehicle body.
|
(b) Pull back on one of the ends of the rear door outside stripe to remove it. HINT: When pulling on the rear door outside stripe, pull it parallel to the vehicle body. |
|
|
|