EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Front Door): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022

Last Modified: 05-13-2024	6.11:8.1.0	Doc ID: RM10000000270MB
Model Year Start: 2023	Model: GR Corolla	Prod Date Range: [09/2022 - 11/2022]
Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Front Door): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedures are not Performed	Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
Door glass1 Door glass run1 Door belt moulding1 Door glass weatherstrip inner1	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Key-off operation function Catch protection function Window open warning function

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Front Camera System	Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed	Necessary Procedures	Link
Power Door Lock Control System Back door opener	Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

Use the same procedure for the RH side and LH side.

The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE DECK BOARD ASSEMBLY

Click here

3. REMOVE SPARE WHEEL CUSHION

Click here

4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Click here

5. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

Click here

6. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY

Click here

7. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here

8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here

9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

10. REMOVE DOOR UPPER FRAME GARNISH

Click here

11. REMOVE FRONT DOOR VENT SEAL

Click here

12. REMOVE NO. 3 FRONT DOOR SERVICE HOLE COVER

Click here

13. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here

14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here

15. REMOVE FRONT DOOR GLASS RUN

Click here

16. DISCONNECT FRONT DOOR WEATHERSTRIP

Click here

17. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY

Click here

18. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP WITH FRONT DOOR FIX WINDOW GLASS

Click here

19. REMOVE FRONT DOOR OUTSIDE STRIPE

HINT:

When removing the front door outside stripe, heat the vehicle body and front door outside stripe using a heat light.

Heating Temperature

Item	Temperature
Front Door Outside Stripe and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the front door outside stripe and vehicle body.

(b) Pull back on one of the ends of the front door outside stripe to remove it.

HINT:

When pulling on the front door outside stripe, pull it parallel to the vehicle body.

20. REMOVE NO. 2 FRONT DOOR STRIPE

HINT:

When removing the No. 2 front door stripe, heat the vehicle body and No. 2 front door stripe using a heat light.

Heating Temperature

Item	Temperature
No. 2 Front Door Stripe and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the No. 2 front door stripe and vehicle body.

(b) Pull back on one of the ends of the No. 2 front door stripe to remove it.

HINT:

When pulling on the No. 2 front door stripe, pull it parallel to the vehicle body.