Last Modified: 07-31-2024 6.11:8.1.0 Doc ID: RM10000000270M9
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: EXTERIOR PANELS / TRIM: REAR DOOR WINDOW FRAME MOULDING: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
  • Door glass*1
  • Door glass run*1
  • Door belt moulding*1
  • Door glass weatherstrip inner*1

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

for TMC Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (for TMC Made): REGISTRATION

except TMC Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (except TMC Made): INITIALIZATION

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
  • Door glass*1
  • Door glass run*1
  • Door belt moulding*1
  • Door glass weatherstrip inner*1

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

for TMC Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (for TMC Made): REGISTRATION

for TMMMS Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (except TMC Made): INITIALIZATION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for TMC Made: Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION

for TMMMS Made: Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

  • for HV Model:

    Learning completes when vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    Front Camera System (for TMC Made)

    Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM (for TMC Made): INITIALIZATION

  • for Gasoline Model:

    Learning completes when vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link
    *1: for GR Model

    *2: except GR Model

    Front Camera System (for TMC Made)
    • Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
    • Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM (for TMC Made): INITIALIZATION

    Pre-collision System (for TMMMS Made)

    Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: PRE-COLLISION SYSTEM (for TMMMS Made): INITIALIZATION

    Lane Tracing Assist System (for TMMMS Made)

    Lane Departure Alert System (for TMMMS Made)

    Learning completes when vehicle is operated normally

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link
    *1: for Hatchback

    Power Door Lock Control System

    • Back door opener*1

    Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for TMC Made): INITIALIZATION

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE REAR DOOR BELT MOULDING

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL

2. REMOVE REAR DOOR WINDOW FRAME MOULDING (CENTER PILLAR SIDE)

HINT:

When removing the rear door window frame moulding (center pillar side), heat the vehicle body and rear door window frame moulding (center pillar side) using a heat light.

Heating Temperature

Item

Temperature

Vehicle Body

40 to 60°C (104 to 140°F)

Rear Door Window Frame Moulding (Center Pillar Side)

20 to 30°C (68 to 86°F)

CAUTION:

  • Do not touch the heat light and heated parts, touching the heat light may result in burns.
  • Touching heated parts for a long time may result in burns.

*a

Heated Part

*b

Heat Light

NOTICE:

Do not heat the vehicle body or rear door window frame moulding (center pillar side) excessively.

(a) Using a heat light, heat the rear door window frame moulding (center pillar side).

(b) Using a moulding remover, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the rear door window frame moulding (center pillar side).

*a

Double-sided Tape

*b

Caulking Sponge

3. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disengage the 6 clips and disconnect the rear door weatherstrip.

4. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING (for Hatchback)

(a) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(c) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 5 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(d) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

(e) Disengage the guide to remove the rear door upper window frame moulding.

5. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING (for Sedan)

(a) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(c) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(d) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

(e) Disengage the guide to remove the rear door upper window frame moulding.

6. REMOVE REAR DOOR REAR WINDOW FRAME MOULDING (for Sedan)

(a) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(c) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 2 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(d) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

(e) Remove the rear door rear window frame moulding.