Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM10000000270M8
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: EXTERIOR PANELS / TRIM: FRONT DOOR WINDOW FRAME MOULDING: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
  • Door glass*1
  • Door glass run*1
  • Door belt moulding*1
  • Door glass weatherstrip inner*1

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

for TMC Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (for TMC Made): REGISTRATION

except TMC Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (except TMC Made): INITIALIZATION

Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedures are not Performed

Link
*1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation.
  • Door glass*1
  • Door glass run*1
  • Door belt moulding*1
  • Door glass weatherstrip inner*1

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

for TMC Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (for TMC Made): REGISTRATION

for TMMMS Made: 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM (except TMC Made): INITIALIZATION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

for TMC Made: Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION

for TMMMS Made: Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMMMS Made): PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

HINT:

When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

  • for HV Model:

    Learning completes when vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link

    Front Camera System (for TMC Made)

    Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM (for TMC Made): INITIALIZATION

  • for Gasoline Model:

    Learning completes when vehicle is driven

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link
    *1: for GR Model

    *2: except GR Model

    Front Camera System (for TMC Made)
    • Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
    • Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM (for TMC Made): INITIALIZATION

    Pre-collision System (for TMMMS Made)

    Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: PRE-COLLISION SYSTEM (for TMMMS Made): INITIALIZATION

    Lane Tracing Assist System (for TMMMS Made)

    Lane Departure Alert System (for TMMMS Made)

    Learning completes when vehicle is operated normally

    Effect/Inoperative Function When Necessary Procedures are not Performed

    Necessary Procedures

    Link
    *1: for Hatchback

    Power Door Lock Control System

    • Back door opener*1

    Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

    2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for TMC Made): INITIALIZATION

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT DOOR BELT MOULDING

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL

2. REMOVE FRONT DOOR WINDOW FRAME MOULDING (CENTER PILLAR SIDE)

HINT:

When removing the front door window frame moulding (center pillar side), heat the vehicle body and front door window frame moulding (center pillar side) using a heat light.

Heating Temperature

Item

Temperature

Vehicle Body

40 to 60°C (104 to 140°F)

Front Door Window Frame Moulding (Center Pillar Side)

20 to 30°C (68 to 86°F)

CAUTION:

  • Do not touch the heat light and heated parts, touching the heat light may result in burns.
  • Touching heated parts for a long time may result in burns.

*a

Heated Part

*b

Heat Light

NOTICE:

Do not heat the vehicle body or moulding excessively.

(a) Using a heat light, heat the front door window frame moulding (center pillar side).

(b) Using a moulding remover, disengage the clip and guide, and separate the double-sided tape and caulking sponge to remove the front door window frame moulding (center pillar side).

*a

Double-sided Tape

*b

Caulking Sponge

3. DISCONNECT FRONT DOOR WEATHERSTRIP

(a) Disengage the 6 clips and disconnect the front door weatherstrip.

4. REMOVE FRONT DOOR WINDOW FRAME MOULDING (FRONT PILLAR SIDE)

(a) Disconnect each connector.

(b) Disengage each clamp.

(c) Remove the 5 bolts and front door panel sub-assembly.

NOTICE:

To prevent damage, when removing the front door panel sub-assembly, make sure that there are enough people available to hold it securely.

(d) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(e) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(f) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 2 rivets and front door window frame moulding (front pillar side).

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(g) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

5. REMOVE FRONT DOOR UPPER WINDOW FRAME MOULDING

(a) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(c) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(d) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

(e) Disengage the guide to remove the front door upper window frame moulding from the door frame.