- Door glass*1
- Door glass run*1
- Door belt moulding*1
- Door glass weatherstrip inner*1
| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM10000000270M6 |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation. | |||
|
|
Initialize power window control system |
|
for TMC Made:
except TMC Made:
|
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedures are not Performed |
Link |
|---|---|---|---|
| *1: Even when not replacing the part, it is necessary to perform the specified necessary procedures afterinstallation. | |||
|
Initialize power window control system |
|
for TMC Made:
for TMMMS Made:
|
CAUTION:
Be sure to read Precaution thoroughly before servicing.
for TMC Made: Click here
![2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM (for TMC Made): PRECAUTION](/t3Portal/stylegraphics/info.gif)
for TMMMS Made: Click here
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for GR Model *2: except GR Model
Front Camera System (for TMC Made)
- Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
- Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more.*2
Pre-collision System (for TMMMS Made)
Drive the vehicle straight ahead at 35 km/h (9 mph) or more for 5 seconds or more.
Lane Tracing Assist System (for TMMMS Made)
Lane Departure Alert System (for TMMMS Made)
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
*1: for Hatchback Power Door Lock Control System
- Back door opener*1
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch (for Gasoline Model) or power switch (for HV Model) off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. REMOVE DECK BOARD ASSEMBLY (for G16E-GTS)
Click here
3. REMOVE SPARE WHEEL CUSHION (for G16E-GTS)
Click here
4. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for G16E-GTS: Click here
for M20A-FKS: Click here
for 2ZR-FAE: Click here
for 2ZR-FXE: Click here
5. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG
Click here
6. REMOVE FRONT DOOR ASSIST GRIP ASSEMBLY
Click here
7. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
8. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
10. REMOVE DOOR UPPER FRAME GARNISH
Click here
11. REMOVE FRONT DOOR VENT SEAL
Click here
12. REMOVE NO. 3 FRONT DOOR SERVICE HOLE COVER
Click here
13. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
15. REMOVE FRONT DOOR GLASS RUN
Click here
16. DISCONNECT FRONT DOOR WEATHERSTRIP
(a) Disconnect the front door weatherstrip until the screw of the front door front lower frame sub-assembly is visible.
17. REMOVE FRONT DOOR FRONT LOWER FRAME SUB-ASSEMBLY
Click here
18. REMOVE FRONT DOOR FIX WINDOW WEATHERSTRIP WITH FRONT DOOR FIX WINDOW GLASS
Click here
19. REMOVE FRONT DOOR BELT MOULDING
(a) Apply protective tape around the front door belt moulding as shown in the illustration.
|
Protective Tape |
|
Remove in this Direction |
(b) Disengage the 8 claws as shown in the illustration to remove the front door belt moulding.
|
|