Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM10000000270KC |
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [09/2022 - 11/2022] |
Title: K120 / K121 (CVT): K120 TCM: REMOVAL; 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed, or replaced during TCM removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure
|
Necessary Procedure
|
Effect/Inoperative when not Performed
|
Link
|
Replacement of TCM
(If transaxle compensation code read from TCM)
|
|
Vehicle Control History (RoB) are stored
|
|
-
Transfer transaxle compensation code
-
Perform reset memory*1
-
Deceleration sensor zero point calibration*2
-
CVT oil pressure calibration
-
Perform road test to allow TCM to learn
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
for Initialization
for Registration
|
Replacement of TCM
(If transaxle compensation code not read from TCM)
|
|
Vehicle Control History (RoB) are stored
|
|
-
Reset transaxle compensation code
-
Perform reset memory*1
-
Deceleration sensor zero point calibration*2
-
CVT oil pressure calibration
-
Perform road test to allow TCM to learn
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
for Initialization
for Registration
|
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Front Camera System (for TMC Made)
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
Pre-collision System (for TMMMS Made)
|
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
|
|
Lane Tracing Assist System (for TMMMS Made)
|
Lane Departure Alert System (for TMMMS Made)
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
Click here
4. REMOVE REAR ENGINE UNDER COVER LH
Click here
5. REMOVE TCM
(a) Remove the bolt to disconnect the engine wire from the No. 2 transmission control ECU bracket.
|
|
(b) Disengage the claw, rotate the lever and disconnect the TCM connector.
|
Remove in this Direction
|
(c) Remove the 2 bolts and TCM from the continuously variable transaxle assembly.
|
|
6. REMOVE NO. 1 TRANSMISSION CONTROL ECU BRACKET
(a) Remove the 2 screws and No. 1 transmission control ECU bracket from the TCM.
|
|
7. REMOVE NO. 2 TRANSMISSION CONTROL ECU BRACKET
(a) Remove the 2 screws and No. 2 transmission control ECU bracket from the TCM.
|
|
|