Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026ZJV |
Model Year Start: 2023 |
Model: Corolla Hatchback |
Prod Date Range: [09/2022 - 11/2022] |
Title: M20A-FKS (ENGINE CONTROL): ECM: REMOVAL; 2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Replacement of ECM
|
Vehicle Identification Number (VIN) registration
|
MIL comes on
|
|
|
Vehicle Control History (RoB) are stored
|
|
ECU communication ID registration (Immobiliser system)
|
Engine start function
|
for TMC Made
for TMMMS Made
|
-
Perform reset memory
-
CVT oil pressure calibration
-
Perform road test to allow TCM to learn
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
for K120 Initialization
for K120 Registration
|
Replacement of ECM*1
|
Code registration (Smart Key System (for Gasoline Model, Start Function))
|
-
Wireless Door Lock Control System (for Gasoline Model with Smart Key System)
-
Smart Key System (for Gasoline Model, Entry Function)
-
Smart Key System (for Gasoline Model, Start Function)
-
Steering lock function*3
|
for TMC Made
for TMMMS Made
|
Replacement of ECM*2
|
Code registration (Immobiliser system)
|
-
Engine start
-
Telematics System
|
|
NOTICE:
If the ECM has been struck or dropped, replace it.
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Front Camera System (for TMC Made)
|
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
|
|
Pre-collision System (for TMMMS Made)
|
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
|
|
Lane Tracing Assist System (for TMMMS Made)
|
Lane Departure Alert System (for TMMMS Made)
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedure
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
3. REMOVE RADIATOR SUPPORT OPENING COVER
-
for Hatchback except GR
Click here
-
for Sedan with Illumination
Click here
-
for Sedan without Illumination
Click here
4. REMOVE INLET NO. 1 AIR CLEANER
-
for TMC Made
Click here
-
except TMC Made
Click here
5. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE
Click here
6. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Click here
7. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
(b) Disengage the guide to remove the air cleaner case sub-assembly.
8. REMOVE ECM
(a) Disengage the claw and 2 guides to remove the No. 1 relay block cover from the No. 1 engine room relay block and No. 1 junction block assembly.
|
|
(b) Disconnect the 3 connectors from the No. 1 engine room relay block and No. 1 junction block assembly.
|
|
(c) Disengage the 2 claws to separate the engine wire from the No. 1 engine room relay block and No. 1 junction block assembly.
(d) Raise the 2 lock levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.
NOTICE:
After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.
|
|
(e) Remove the bolt and disengage the wire harness clamp to separate the engine wire.
(f) Remove the grommet.
(g) Remove the bolt and nut.
|
|
(h) Disengage the guide to remove the ECM.
NOTICE:
If the ECM has been struck or dropped, replace it.
9. REMOVE NO. 2 ECM BRACKET
(a) Remove the 2 screws and No. 2 ECM bracket from the ECM.
|
|
10. REMOVE NO. 1 ECM BRACKET
(a) Remove the 2 screws and No. 1 ECM bracket from the ECM.
|
|
|