Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000026ZJD
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: BRAKE SYSTEM (OTHER): BRAKE PEDAL (for Gasoline Model): REMOVAL; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake pedal support assembly removal/installation are shown below.

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Items for which learning is completed by driving the vehicle

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedures

Link

*1: for GR Model

*2: except GR Model

Front Camera System (for TMC Made)

  • Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
  • Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: FRONT CAMERA SYSTEM (for TMC Made): INITIALIZATION

Pre-collision System (for TMMMS Made)

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; ADVANCED DRIVER ASSISTANCE SYSTEM: PRE-COLLISION SYSTEM (for TMMMS Made): INITIALIZATION

Lane Tracing Assist System (for TMMMS Made)

Lane Departure Alert System (for TMMMS Made)

Learning completes when vehicle is operated normally

Effect/Inoperative Function when Necessary Procedure not Performed

Necessary Procedures

Link

*1: for Hatchback

Power Door Lock Control System

  • Back door opener*1

Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.

2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; DOOR LOCK: POWER DOOR LOCK CONTROL SYSTEM (for TMC Made): INITIALIZATION

NOTICE:

  • After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) battery terminal.
  • When the cable is disconnected from the negative (-) battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) battery terminal. (for Audio and Visual System (for Single Knob Type))

PROCEDURE

1. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: KNEE AIRBAG ASSEMBLY: REMOVAL

2. REMOVE FRONT NO. 1 CONSOLE BOX INSERT

except G16E-GTS: Click here 2023 MY Corolla Corolla Hatchback Corolla HV [09/2022 - 11/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (except G16E-GTS): REMOVAL+

for G16E-GTS: Click here 2023 MY GR Corolla [09/2022 - 11/2022]; INTERIOR PANELS / TRIM: FRONT CONSOLE BOX (for G16E-GTS): REMOVAL+

3. REMOVE NO. 1 AIR DUCT

Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; STEERING COLUMN: STEERING COLUMN ASSEMBLY: REMOVAL+

4. REMOVE STOP LIGHT SWITCH ASSEMBLY

Click here 2019 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [06/2018 -        ]; LIGHTING (EXT): STOP LIGHT SWITCH: REMOVAL+

5. REMOVE BRAKE PEDAL RETURN SPRING

(a) Remove the brake pedal return spring from the brake pedal support assembly and push rod pin.

6. REMOVE PUSH ROD PIN

(a) Remove the clip and push rod pin to separate the brake pedal support assembly from the brake master cylinder push rod clevis.

7. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY

(a) Disengage the clamp to separate the wire harness from the brake pedal support assembly.

(b) Remove the bolt and separate the brake pedal support assembly from the instrument panel reinforcement assembly.

(c) Remove the 2 clips.

Nut

Clip

(d) Remove the 4 nuts and brake pedal support assembly.

(e) Remove the nut from the brake pedal support assembly.

8. REMOVE STOP LIGHT SWITCH MOUNTING ADJUSTER

(a) Disengage the 2 claws and remove the stop light switch mounting adjuster.

9. REMOVE BRAKE PEDAL PAD

(a) Remove the brake pedal pad from the brake pedal support assembly.