Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026ZF3 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: PARK ASSIST / MONITORING: REAR VIEW MONITOR SYSTEM (for Single Knob Radio and Display Receiver): Image from Camera for Rear View Monitor is Abnormal; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] |
Image from Camera for Rear View Monitor is Abnormal
|
DESCRIPTION
The video signal of the rear television camera assembly is transmitted to the radio and display receiver assembly.
WIRING DIAGRAM
PROCEDURE
1.
|
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
|
(a) Disconnect the I175 radio and display receiver assembly connector.
(b) Disconnect the V22*1 or O115*2 rear television camera assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I175-30 (CA+) - V22*1 or O115*2-6 (CB+)
|
Always
|
Below 1 Ω
|
I175-28 (V+) - V22*1 or O115*2-3 (CV+)
|
Always
|
Below 1 Ω
|
I175-29 (V-) - V22*1 or O115*2-2 (CV-)
|
Always
|
Below 1 Ω
|
I175-27 (CGND) - V22*1 or O115*2-5 (CGND)
|
Always
|
Below 1 Ω
|
I175-26 (CSLD) - Body ground
|
Always
|
Below 1 Ω
|
I175-30 (CA+) or V22*1 or O115*2-6 (CB+) - Body ground
|
Always
|
10 kΩ or higher
|
I175-28 (V+) or V22*1 or O115*2-3 (CV+) - Body ground
|
Always
|
10 kΩ or higher
|
I175-29 (V-) or V22*1 or O115*2-2 (CV-) - Body ground
|
Always
|
10 kΩ or higher
|
I175-27 (CGND) or V22*1 or O115*2-5 (CGND) - Body ground
|
Always
|
10 kΩ or higher
|
-
*1: for Hatchback Model
-
*2: for Sedan Model
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
2.
|
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
|
(a) Reconnect the I175 radio and display receiver assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I175-29 (V-) - Body ground
|
Always
|
Below 1 Ω
|
I175-27 (CGND) - Body ground
|
Always
|
Below 1 Ω
|
|
|
*a
|
Component with harness connected
(Radio and Display Receiver Assembly)
|
|
|
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
I175-30 (CA+) - I175-27 (CGND)
|
Ignition switch ACC
|
5.5 to 7.05 V
|
OK
|
|
|
3.
|
INSPECT REAR TELEVISION CAMERA ASSEMBLY
|
(a) Reconnect the V22*1 or O115*2 rear television camera assembly connector.
-
*1: for Hatchback Model
-
*2: for Sedan Model
(b) Using an oscilloscope, check the waveform of the rear television camera assembly.
HINT:
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.
OK:
Waveform is similar to that shown in the illustration.
Item
|
Content
|
Measurement terminal
|
I175-28 (V+) - I175-29 (V-)
|
Measurement setting
|
200 mV/DIV., 50 μs./DIV.
|
Condition
|
Ignition switch ON, reverse (R) selected
|
*a
|
Component with harness connected
(Radio and Display Receiver Assembly)
|
*a
|
Waveform 1 (camera lens is not covered, displaying an image)
|
*b
|
Waveform 2 (camera lens is covered, blacking out the screen)
|
*c
|
Synchronization Signal
|
*d
|
Video Waveform
|
HINT:
-
The video waveform changes according to the image sent by the rear television camera assembly.
-
The video waveform is constantly output when the ignition switch is turned to ACC.
-
Make sure that the rear camera is enabled in general settings.
NG |
|
REPLACE REAR TELEVISION CAMERA ASSEMBLY
for Sedan: Click here
for Hatchback: Click here
|
|