| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000026Z9V |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM (for TMC Made, and Gasoline Model, with Manual Air Conditioning System for Electrical Control Type): B143A87; Lost Communication with Air Inlet Damper Control Servo Motor LIN Missing Message; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022] | ||
|
DTC |
B143A87 |
Lost Communication with Air Inlet Damper Control Servo Motor LIN Missing Message |
DESCRIPTION
The air conditioning harness assembly connects the air conditioning amplifier assembly and No. 1 blower damper servo sub-assembly.
The No. 1 blower damper servo sub-assembly sends damper position information to the air conditioning amplifier assembly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
|---|---|---|---|---|
|
B143A87 |
Lost Communication with Air Inlet Damper Control Servo Motor LIN Missing Message |
Diagnosis Condition:
Malfunction:
Detection Time:
|
|
Memorized |
DTC Detection Condition Combination Table
|
Vehicle Condition |
|||
|---|---|---|---|
|
Pattern 1 |
Pattern 2 |
||
|
Diagnosis Condition |
Ignition switch ON |
○ |
○ |
|
Malfunction |
Error in communication line between air conditioning amplifier assembly and No. 1 blower damper servo sub-assembly |
○ |
- |
|
Open in communication line between air conditioning amplifier assembly and No. 1 blower damper servo sub-assembly |
- |
○ |
|
|
Detection Time |
Continuously for 10 seconds or more |
Continuously for 10 seconds or more |
|
|
Trip Count |
1 trip |
1 trip |
|
HINT:
If the conditions of either of these patterns are detected, a DTC will be stored.
WIRING DIAGRAM
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Check for DTCs.
Body Electrical > Air Conditioner > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC B142A88 is output |
A |
|
DTC B142A88 is not output |
B |
| A |
|
|
|
2. |
INSPECT AIR CONDITIONING HARNESS ASSEMBLY |
(a) Disconnect the m4 No. 1 air conditioning radiator damper servo sub-assembly connector.
(b) Disconnect the m1 No. 1 blower damper servo sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
m4-1 (M-) - m1-5 (M-) |
Always |
Below 1 Ω |
|
m4-2 (M+) - m1-4 (M+) |
Always |
Below 1 Ω |
|
m4-3 (STE2) - m1-3 (STE2) |
Always |
Below 1 Ω |
|
m4-4 (STE1) - m1-2 (STE1) |
Always |
Below 1 Ω |
|
m4-5 (GND) - m1-1 (GND) |
Always |
Below 1 Ω |
|
m4-1 (M-) or m1-5 (M-) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
m4-2 (M+) or m1-4 (M+) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
m4-3 (STE2) or m1-3 (STE2) - Other terminals and body ground |
Always |
10 kΩ or higher |
|
m4-4 (STE1) or m1-2 (STE1) - Other terminals and body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
|
|