Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000026Z9U
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM (for TMC Made, and Gasoline Model, with Manual Air Conditioning System for Electrical Control Type): B142A88; Servo Motor LIN Communication Bus off; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]

DTC

B142A88

Servo Motor LIN Communication Bus off

DESCRIPTION

The air conditioning harness assembly connects the air conditioning amplifier assembly and the servo motors.

The air conditioning amplifier assembly supplies power and sends operation instructions to each servo motor through the air conditioning harness assembly.

Each servo motor sends damper position information to the air conditioning amplifier assembly.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

B142A88

Servo Motor LIN Communication Bus off

Diagnosis Condition:

  • Ignition switch ON

Malfunction:

  • Error or open in communication line between air conditioning amplifier assembly and each servo motor

Detection Time:

  • Continuously for 10 seconds or more
  • Air conditioning harness assembly
  • No. 1 air conditioning radiator damper servo sub-assembly
  • Air conditioning amplifier assembly

Memorized

DTC Detection Condition Combination Table

 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

Ignition switch ON

Malfunction

Error in communication line between air conditioning amplifier assembly and each servo motor

-

Open in communication line between air conditioning amplifier assembly and each servo motor

-

Detection Time

Continuously for 10 seconds or more

Continuously for 10 seconds or more

Trip Count

1 trip

1 trip

HINT:

If the conditions of either of these patterns are detected, a DTC will be stored.

WIRING DIAGRAM

PROCEDURE

1.

CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NOTICE:

When inspecting the air conditioning amplifier assembly, be careful not to cause a short.

(a) Disconnect the m3 air conditioning amplifier assembly connector.

*a

Component without harness connected

(Air Conditioning Amplifier Assembly)

-

-

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

m3-2 (BUSG) - Body ground

Always

Below 1 Ω

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

m3-4 (BUSB) - m3-2 (BUSG)

Ignition switch off

11 to 14 V

(d) Using an oscilloscope, check the waveform.

Item

Content

Tester Connection

m3-3 (BUS) - m3-2 (BUSG)

Tool Setting

2 V/DIV., 20 μs/DIV.

Condition

Ignition switch ON

OK:

The waveform displays properly.

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

OK

2.

CHECK AIR CONDITIONING HARNESS ASSEMBLY

(a) Disconnect the m3 air conditioning amplifier assembly connector.

(b) Disconnect the m4 No. 1 air conditioning radiator damper servo sub-assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

m3-2 (BUSG) - m4-6 (BUSG)

Always

Below 1 Ω

m3-3 (BUS) - m4-7 (BUS)

Always

Below 1 Ω

m3-4 (BUSB) - m4-8 (BUSB)

Always

Below 1 Ω

OK

REPLACE NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY

NG

REPLACE AIR CONDITIONING HARNESS ASSEMBLY