| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000026Z3M |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - ] |
| Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for 8 Inch Display Type (w/ Single Knob Type) or 10.5 Inch Display Type): USB Audio System Recognition/Play Error; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] | ||
|
USB Audio System Recognition/Play Error |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for Knobless Radio and Display Receiver): PRECAUTION](/t3Portal/stylegraphics/info.gif)
HINT:
- When many folders or files exist in the USB storage device, it may take a while to begin playback.
- When using a USB storage device, files that are protected by copyright or encrypted cannot be played
- If a USB hub is being used, remove it.
-
When files on the USB storage device are not played in the sorted order, perform the following procedure.
- Assign a number to the start of each file name.
- Move the files to a folder and copy each folder to the USB storage device.
PROCEDURE
|
1. |
CHECK USB STORAGE DEVICE OR "iPod" |
(a) Disconnect the USB storage device or "iPod" from the No. 1 stereo jack adapter assembly.
(b) Check that playable files exist in the USB storage device or "iPod".
(c) Check that the USB storage device or "iPod" being used by the customer is a compatible version and format.
|
Result |
Proceed to |
|---|---|
|
The format of the USB storage device is compatible The version of the "iPod" is compatible (for Sedan) |
A |
|
The format of the USB storage device is compatible The version of the "iPod" is compatible (except Sedan) |
B |
|
Playable files do not exist The format of the USB storage device is not compatible The version of the "iPod" is not compatible |
C |
| B |
|
| C |
|
END |
|
|
2. |
INSPECT ANTENNA CORD SUB-ASSEMBLY |
(a) Disconnect the x5 radio and display receiver assembly connector.
(b) Disconnect the t4 No. 1 stereo jack adapter assembly connector.
(c) Disconnect the Ix1 antenna cord sub-assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
x5-1 (USV1) - x4-3 (Vbus) |
Always |
Below 1 Ω |
|
x5-2 (US1-) - t4-4 (D-) |
Always |
Below 1 Ω |
|
x5-3 (US1+) - x4-1 (D+) |
Always |
Below 1 Ω |
|
x5-4 (UGD1) - x4-2 (Vgnd) |
Always |
Below 1 Ω |
|
x5-5 (USG1) - x4-5 (UJSS) |
Always |
Below 1 Ω |
|
Ix1-5 - x4-6 (+B) |
Always |
Below 1 Ω |
|
Ix1-1 - x4-8 (GND) |
Always |
Below 1 Ω |
|
Ix1-3 - x4-7 (ADPG) |
Always |
Below 1 Ω |
|
x5-1 (USV1) or x4-3 (Vbus) - Body ground |
Always |
10 kΩ or higher |
|
x5-2 (US1-) or x4-4 (D-) - Body ground |
Always |
10 kΩ or higher |
|
x5-3 (US1+) or x4-1 (D+) - Body ground |
Always |
10 kΩ or higher |
|
x5-4 (UGD1) or x4-2 (Vgnd) - Body ground |
Always |
10 kΩ or higher |
|
x5-5 (USG1) or x4-5 (UJSS) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-5 or x4-6 (+B) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-1 or x4-8 (GND) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-3 or x4-7 (ADPG) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPLACE ANTENNA CORD SUB-ASSEMBLY
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (ANTENNA CORD SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
(a) Disconnect the Ix1 antenna cord sub-assembly connector.
(b) Disconnect the I55 and I175 radio and display receiver assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Ix1-5 - I155-3 (+B) |
Always |
Below 1 Ω |
|
Ix1-1 - I155-2 (GND2) |
Always |
Below 1 Ω |
|
Ix1-3 - I175-6 (ADPG) |
Always |
Below 1 Ω |
|
Ix1-5 or I155-3 (+B) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-1 or I155-2 (GND2) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-3 or I175-6 (ADPG) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (USV1, +B) |
(a) Disconnect the x4 No. 1 stereo jack adapter assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
x4-3 (Vbus) - x4-2 (Vgnd) |
Ignition switch ON |
4.5 to 5.5 V |
|
x4-6 (+B) - x4-8 (GND) |
Always |
11 to 14 V |
HINT:
Measure the voltage with the radio and display receiver assembly connectors connected.
| NG |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
|
5. |
FORMAT USB DEVICE OR INITIALIZE "iPod" AND RECHECK |
(a) Format the USB storage device or initialize the "iPod" to delete the audio files.
NOTICE:
When formatting the USB storage device or initializing the "iPod", all audio files stored in the device will be deleted. Make sure to back up the audio files before performing this procedure.
(b) Restore the data and check if the problem can be reproduced.
|
Result |
Proceed to |
|---|---|
|
Malfunction disappears |
A |
|
Malfunction occurs. |
B |
| A |
|
END |
|
|
6. |
CHECK USB STORAGE DEVICE OR "iPod'" |
(a) Disconnect the USB storage device or "iPod" from the No. 1 stereo jack adapter assembly.
(b) Turn the ignition switch from off to ON
HINT:
If another USB storage device or "iPod" is to be connected, it is necessary to turn the ignition switch off in order for the device to be detected.
(c) Connect a known good USB storage device or "iPod" to the No. 1 stereo jack adapter assembly.
HINT:
- When a USB storage device is used, replace it with another device and perform the inspection.
- When an "iPod" is used, replace it with another device and perform the inspection.
(d) Perform the operation again and check if the problem symptom recurs.
|
Result |
Proceed to |
|---|---|
|
Malfunction disappears |
A |
|
Malfunction occurs |
B |
| A |
|
END |
|
|
7. |
CHECK NO. 1 STEREO JACK ADAPTER ASSEMBLY |
(a) Replace the No.1 stereo jack adapter assembly with a new or known good one.
Click here
(b) Check if the problem symptom recurs.
|
Result |
Proceed to |
|---|---|
|
Malfunction disappears |
A |
|
Malfunction occurs |
B |
| A |
|
END (NO. 1 STEREO JACK ADAPTER ASSEMBLY MALFUNCTION) |
| B |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
8. |
INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY |
(a) Disconnect the x5 radio and display receiver assembly connector.
(b) Disconnect the x4 No. 1 stereo jack adapter assembly connector.
(c) Disconnect the Ix1 No. 2 antenna cord sub-assembly connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
x5-1 (USV1) - x4-3 (Vbus) |
Always |
Below 1 Ω |
|
x5-2 (US1-) - x4-4 (D-) |
Always |
Below 1 Ω |
|
x5-3 (US1+) - x4-1 (D+) |
Always |
Below 1 Ω |
|
x5-4 (UGD1) - x4-2 (Vgnd) |
Always |
Below 1 Ω |
|
x5-5 (USG1) - x4-5 (UJSS) |
Always |
Below 1 Ω |
|
Ix1-5 - x4-6 (+B) |
Always |
Below 1 Ω |
|
Ix1-1 - x4-8 (GND) |
Always |
Below 1 Ω |
|
Ix1-3 - x4-7 (ADPG) |
Always |
Below 1 Ω |
|
x5-1 (USV1) or x4-3 (Vbus) - Body ground |
Always |
10 kΩ or higher |
|
x5-2 (US1-) or x4-4 (D-) - Body ground |
Always |
10 kΩ or higher |
|
x5-3 (US1+) or x4-1 (D+) - Body ground |
Always |
10 kΩ or higher |
|
x5-4 (UGD1) or x4-2 (Vgnd) - Body ground |
Always |
10 kΩ or higher |
|
x5-5 (USG1) or x4-5 (UJSS) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-5 or x4-6 (+B) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-1 or x4-8 (GND) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-3 or x4-7 (ADPG) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
|
|
|
9. |
CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
(a) Disconnect the I1 No. 2 antenna cord sub-assembly connector.
(b) Disconnect the I55 and I175 radio and display receiver assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
Ix1-5 - I55-3 (+B) |
Always |
Below 1 Ω |
|
Ix1-1 - I55-2 (GND2) |
Always |
Below 1 Ω |
|
Ix1-3 - I175-6 (ADPG) |
Always |
Below 1 Ω |
|
Ix1-5 or I55-3 (+B) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-1 or I55-2 (GND2) - Body ground |
Always |
10 kΩ or higher |
|
Ix1-3 or I175-6 (ADPG) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
10. |
INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (USV1, +B) |
(a) Disconnect the x4 No. 1 stereo jack adapter assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
x4-3 (Vbus) - x4-2 (Vgnd) |
Ignition switch ON |
4.5 to 5.5 V |
|
x4-6 (+B) - x4-8 (GND) |
Always |
11 to 14 V |
HINT:
Measure the voltage with the radio and display receiver assembly connectors connected.
| NG |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
|
11. |
FORMAT USB DEVICE OR INITIALIZE "iPod" AND RECHECK |
(a) Format the USB storage device or initialize the "iPod" to delete the audio files.
NOTICE:
When formatting the USB storage device or initializing the "iPod", all audio files stored in the device will be deleted. Make sure to back up the audio files before performing this procedure.
(b) Restore the data and check if the problem can be reproduced.
|
Result |
Proceed to |
|---|---|
|
Malfunction disappears |
A |
|
Malfunction occurs. |
B |
| A |
|
END |
|
|
12. |
CHECK USB STORAGE DEVICE OR "iPod'" |
(a) Disconnect the USB storage device or "iPod" from the No. 1 stereo jack adapter assembly.
(b) Turn the ignition switch from off to ON
HINT:
If another USB storage device or "iPod" is to be connected, it is necessary to turn the ignition switch off in order for the device to be detected.
(c) Connect a known good USB storage device or "iPod" to the No. 1 stereo jack adapter assembly.
HINT:
- When a USB storage device is used, replace it with another device and perform the inspection.
- When an "iPod" is used, replace it with another device and perform the inspection.
(d) Perform the operation again and check if the problem symptom recurs.
|
Result |
Proceed to |
|---|---|
|
Malfunction disappears |
A |
|
Malfunction occurs |
B |
| A |
|
END |
|
|
13. |
CHECK NO. 1 STEREO JACK ADAPTER ASSEMBLY |
(a) Replace the No.1 stereo jack adapter assembly with a new or known good one.
Click here
(b) Check if the problem symptom recurs.
|
Result |
Proceed to |
|---|---|
|
Malfunction disappears |
A |
|
Malfunction occurs |
B |
| A |
|
END (NO. 1 STEREO JACK ADAPTER ASSEMBLY MALFUNCTION) |
| B |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
|