| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000026Q07 |
| Model Year Start: 2023 | Model: Corolla HV | Prod Date Range: [09/2022 - ] |
| Title: HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): P0A8100,P0A8115; Hybrid/EV Battery Cooling Fan 1 Control Circuit High; 2023 - 2025 MY Corolla HV [09/2022 - ] | ||
|
DTC |
P0A8100 |
Hybrid/EV Battery Cooling Fan 1 Control Circuit High |
|
DTC |
P0A8115 |
Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open |
DESCRIPTION
Refer to the description for DTC P0A8111.
Click here
![2023 - 2025 MY Corolla HV [09/2022 - ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): P0A8111,P0A814B; Hybrid/EV Battery Cooling Fan 1 Circuit Short to Ground+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
Note |
|---|---|---|---|---|---|---|
|
P0A8100 |
Hybrid/EV Battery Cooling Fan 1 Control Circuit High |
Both of the following conditions are met:
(1 trip detection logic) |
|
Comes on |
Master warning: Comes on |
SAE Code: P0A85 |
|
P0A8115 |
Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open |
Both of the following conditions are met:
(2 trip detection logic) |
|
Comes on |
Master warning: Comes on |
SAE Code: P0A85 |
HINT:
- "Hybrid/EV Battery Cooling Fan 1 Frequency" is detected when the battery cooling blower assembly is operating and its value changes in proportion to the battery cooling blower assembly speed.
- If the battery cooling blower assembly speed is excessively high, this DTC is stored.
MONITOR DESCRIPTION
If the battery ECU assembly detects that the speed of the battery cooling blower assembly is higher than the target speed, it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs |
P0A85 (INF P0A8100): Hybrid/EV Battery Cooling Fan 1 Control Circuit High P0A85 (INF P0A8115): Hybrid/EV Battery Cooling Fan 1 Circuit Short to Auxiliary Battery or Open |
|
Required sensors/components |
Battery cooling blower assembly |
|
Frequency of operation |
Continuous |
|
Duration |
TMC's intellectual property |
|
MIL operation |
1 driving cycle / 2 driving cycles |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Battery ECU assembly |
DTC P0A85 (INF P0A8100) is not detected DTC P0A85 (INF P0A8115) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the GTS on.
- Enter the following menus: Powertrain / HV Battery / Active Test / Control the Hybrid/EV Battery Cooling Fan.[*1]
-
Select fan mode 6 and operate the battery cooling blower assembly and wait for 60 seconds or more.[*2]
HINT:
- Operation of the battery cooling blower assembly can be confirmed by checking if air is sucked into the air intake port of the intake duct or by operation sounds.
-
[*1] to [*2]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
WIRING DIAGRAM
Refer to the wiring diagram for DTC P0A8111.
Click here
CAUTION / NOTICE / HINT
CAUTION:
Refer to the precautions before inspecting high voltage circuit.
Click here
NOTICE:
-
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
-
When disconnecting and reconnecting the auxiliary battery
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here
PROCEDURE
|
1. |
CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL) |
(a) Check for DTCs.
Powertrain > HV Battery > Trouble Codes
Powertrain > Hybrid Control > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
P0A8100 or P0A8115 only is output, or DTCs except the ones in the table below are also output. |
A |
|
DTCs of hybrid battery system in the table below are output. |
B |
|
DTCs of hybrid control system in the table below are output. |
C |
|
System |
Relevant DTC |
|
|---|---|---|
|
Hybrid battery system |
P060A47 |
Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure |
|
P060B49 |
Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure |
|
|
P060687 |
Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message |
|
|
Hybrid control system |
P0A1F94 |
Hybrid/EV Battery Energy Control Module Unexpected Operation |
(b) Turn the ignition switch off.
| B |
|
GO TO DTC CHART (HYBRID BATTERY SYSTEM) |
| C |
|
|
|
2. |
CHECK BATTERY ECU ASSEMBLY (FREQUENCY) |
Click here
| OK |
|
| NG |
|
|
|