Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000026PZ3
Model Year Start: 2023 Model: Corolla HV Prod Date Range: [09/2022 -           ]
Title: HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): P0B1362; Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure; 2023 - 2025 MY Corolla HV [09/2022 -        ]

DTC

P0B1362

Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure

DESCRIPTION

Refer to the description for DTC P0ABF11.

Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): P0ABF11,...,P1CBB14; Hybrid/EV Battery Current Sensor "A" Circuit Short to Ground+

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Warning Indicate

Note

P0B1362

Hybrid/EV Battery Current Sensor "A"/"B" Signal Compare Failure

A battery current sensor is malfunctioning.*

(1 trip detection logic)

  • HV battery junction block assembly
  • Battery ECU assembly
  • Wire harness or connector

Comes on

Master Warning:

Comes on

SAE Code: P0B13

*: The difference in output of the main and sub battery current sensors is large.

MONITOR DESCRIPTION

If the battery ECU assembly detects a malfunction in a battery current sensor, the battery ECU assembly will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Related DTCs

P0B13 (INF P0B1362): Current sensor malfunction

Required sensors/components

Battery current sensor

Frequency of operation

Continuous

Duration

TMC's intellectual property

MIL operation

Immediately

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

TMC's intellectual property

Other conditions belong to TMC's intellectual property

-

TYPICAL MALFUNCTION THRESHOLDS

TMC's intellectual property

-

COMPONENT OPERATING RANGE

Battery ECU assembly

DTC P0B13 (INF P0B1362) is not detected

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): UTILITY

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): DTC CHECK / CLEAR

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Drive the vehicle on urban roads for approximately 10 minutes.[*1]

    HINT:

    [*1]: Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / HV Battery / Utility / All Readiness.
  8. Check the DTC judgment result.

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

CAUTION:

Refer to the precautions before inspecting high voltage circuit.

Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): PRECAUTION

NOTICE:

  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

  • When disconnecting and reconnecting the auxiliary battery

    HINT:

    When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [11/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

PROCEDURE

1.

CHECK DTC OUTPUT (HV BATTERY, HYBRID CONTROL)

(a) Check for DTCs.

Powertrain > HV Battery > Trouble Codes

Powertrain > Hybrid Control > Trouble Codes

Result

Proceed to

"P0B1362" only is output, or DTCs except the ones in the table below are also output.

A

DTCs of hybrid battery system in the table below are output.

B

DTCs of hybrid control system in the table below are output.

C

System

Relevant DTC

Hybrid battery system

P060A47

Hybrid/EV Battery Energy Control Module Monitoring Processor Watchdog / Safety MCU Failure

P060B49

Hybrid/EV Battery Energy Control Module A/D Processing Internal Electronic Failure

P060687

Hybrid/EV Battery Energy Control Module Processor to Monitoring Processor Missing Message

Hybrid control system

P0A1F94

Hybrid/EV Battery Energy Control Module Unexpected Operation

(b) Turn the ignition switch off.

B

GO TO DTC CHART (HYBRID BATTERY SYSTEM)

C

GO TO DTC CHART (HYBRID CONTROL SYSTEM)

A

2.

CHECK HARNESS AND CONNECTOR (BATTERY ECU ASSEMBLY - HV BATTERY JUNCTION BLOCK ASSEMBLY)

Click here 2023 - 2025 MY Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM (for LITHIUM-ION BATTERY with PA10): P0ABF28; Hybrid/EV Battery Current Sensor "A" Signal Bias Level Out of Range / Zero Adjustment Failure+

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY

Click here 2023 - 2025 MY Corolla Corolla HV [09/2022 -        ]; HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for LITHIUM-ION BATTERY): REMOVAL

NEXT

4.

CLEAR DTC (HV BATTERY)

(a) Clear the DTCs and freeze frame data.

Powertrain > HV Battery > Clear DTCs

(b) Drive the vehicle on urban roads for approximately 10 minutes.

NEXT

5.

CHECK DTC OUTPUT (HV BATTERY)

(a) Check for DTCs.

Powertrain > HV Battery > Trouble Codes

Result

Proceed to

DTCs are not output.

A

P0B1362 is also output.

B

(b) Turn the ignition switch off.

A

END

B

REPLACE BATTERY ECU ASSEMBLY