| Last Modified: 05-13-2024 | 6.11:8.1.0 | Doc ID: RM1000000026PWS |
| Model Year Start: 2023 | Model: Corolla HV | Prod Date Range: [09/2022 - ] |
| Title: HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10): P0A0011,P0A0015; Motor Electronics Coolant Temperature Sensor Circuit Short to Ground; 2023 - 2025 MY Corolla HV [09/2022 - ] | ||
|
DTC |
P0A0011 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Ground |
|
DTC |
P0A0015 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Battery or Open |
DESCRIPTION
Refer to the description for DTC P0A001C.
Click here
![2023 - 2025 MY Corolla HV [09/2022 - ]; HYBRID / BATTERY CONTROL: MOTOR GENERATOR CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10): P0A001C; Motor Electronics Coolant Temperature Sensor Circuit Voltage Out of Range+](/t3Portal/stylegraphics/info.gif)
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
Note |
|---|---|---|---|---|---|---|
|
P0A0011 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Ground |
Short to ground detected in HV coolant temperature sensor circuit (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning: Comes on |
SAE Code: P0A02 |
|
P0A0015 |
Motor Electronics Coolant Temperature Sensor Circuit Short to Battery or Open |
Open or short to +B detected in HV coolant temperature sensor circuit (1 trip detection logic) |
Inverter with converter assembly |
Comes on |
Master Warning: Comes on |
SAE Code: P0A03 |
MONITOR DESCRIPTION
If the motor generator control ECU detects a malfunction in the HV coolant temperature sensor it will illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs |
P0A02 (INF P0A0011): Motor Electronics Coolant Temperature Sensor Range check (Low voltage) P0A03 (INF P0A0015): Motor Electronics Coolant Temperature Sensor Range check (High voltage) |
|
Required sensors/components |
HV coolant temperature sensor |
|
Frequency of operation |
Continuous |
|
Duration |
TMC's intellectual property |
|
MIL operation |
Immediately |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
|
The monitor will run whenever the following DTCs are not stored |
TMC's intellectual property |
|
Other conditions belong to TMC's intellectual property |
- |
TYPICAL MALFUNCTION THRESHOLDS
|
TMC's intellectual property |
- |
COMPONENT OPERATING RANGE
|
Motor generator control ECU |
DTC P0A02 (INF P0A0011) is not detected DTC P0A03 (INF P0A0015) is not detected |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
-
Turn the ignition switch to ON and wait for 5 seconds or more. [*1]
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Enter the following menus: Powertrain / Motor Generator / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform the normal judgment procedure again.
CAUTION / NOTICE / HINT
HINT:
After the repair, clear the DTCs. If the value of Data List item "Inverter Coolant Temperature" is not abnormal (110°C (230°F) or -40°C (-40°F)) when the ignition switch is turned to ON, the condition is judged as normal.
(If DTC P0A0011 is output, 110°C (230°F) will be displayed and if DTC P0A0015 is output, -40°C (-40°F) will be displayed.)
PROCEDURE
|
1. |
REPLACE INVERTER WITH CONVERTER ASSEMBLY |
Click here
| NEXT |
|
COMPLETED |
|
|