| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000026PUF |
| Model Year Start: 2023 | Model: Corolla HV | Prod Date Range: [09/2022 - ] |
| Title: HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10): P314779; Transmission (Shaft) Mechanical Linkage Failure; 2023 - 2025 MY Corolla HV [09/2022 - ] | ||
|
DTC |
P314779 |
Transmission (Shaft) Mechanical Linkage Failure |
DTC SUMMARY
Refer to the DTC summary for DTC P1C7779.
Click here
![2023 - 2025 MY Corolla HV [09/2022 - ]; HYBRID / BATTERY CONTROL: HYBRID CONTROL SYSTEM (for LITHIUM-ION BATTERY with PA10): P1C7779; Engine Failed to Start Mechanical Linkage Failure+](/t3Portal/stylegraphics/info.gif)
DESCRIPTION
Refer to the description for DTC P1C7779.
Click here
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Warning Indicate |
Note |
|---|---|---|---|---|---|---|
|
P314779 |
Transmission (Shaft) Mechanical Linkage Failure |
Drive force from motor (MG2) or the engine cannot be transmitted to the wheels. The engine, generator (MG1), motor (MG2) or hybrid vehicle transaxle assembly does not run smoothly due to a mechanical malfunction. (1 trip detection logic) |
|
Does not come on |
Master Warning: Comes on |
SAE Code: P3147 |
CONFIRMATION DRIVING PATTERN
HINT:
After repair has been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
- Connect the GTS to the DLC3.
- Turn the ignition switch to ON and turn the GTS on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the ignition switch off and wait for 2 minutes or more.
- Turn the ignition switch to ON and turn the GTS on.
- Turn the ignition switch to ON (READY).
- Drive the vehicle at approximately 30 km/h (19 mph) or more for approximately 5 seconds or more using the engine.
- Enter the following menus: Powertrain / Hybrid Control / Utility / All Readiness.
-
Check the DTC judgment result.
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE, perform driving pattern again.
CAUTION / NOTICE / HINT
HINT:
- A seized engine, mechanical malfunction of the hybrid vehicle transaxle can be suspected.
- If this DTC is output, the engine or gears in the transaxle may have seized or foreign matter have been caught in either of them. Therefore, check the engine oil, hybrid transaxle fluid, coolant (for Engine) and coolant (for Inverter) levels.
PROCEDURE
|
1. |
CHECK DTC OUTPUT (ENGINE, MOTOR GENERATOR) |
(a) Check for DTCs.
Powertrain > Engine > Trouble Codes
Powertrain > Motor Generator > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
No DTCs are output, or DTCs except the ones in the table below are also output. |
A |
|
DTCs of SFI system in the tables below are output. |
B |
|
DTCs of Motor Generator Control System in the tables below are output. |
C |
|
System |
Malfunction Content |
Relevant DTC |
|
|---|---|---|---|
|
SFI system |
Sensor and actuator circuit malfunction |
P033511 |
Crankshaft Position Sensor "A" Circuit Short to Ground |
|
P033515 |
Crankshaft Position Sensor "A" Circuit Short to Battery or Open |
||
|
P03352A |
Crankshaft Position Sensor "A" Signal Stuck in Range |
||
|
P033531 |
Crankshaft Position Sensor "A" No Signal |
||
|
Motor generator control system |
Motor resolver malfunction |
P0A3F16 |
Drive Motor "A" Position Sensor Circuit Voltage Below Threshold |
|
P0A3F21 |
Drive Motor "A" Position Sensor Signal Amplitude < Minimum |
||
|
P0A3F22 |
Drive Motor "A" Position Sensor Signal Amplitude > Maximum |
||
|
P0C5013 |
Drive Motor "A" Position Sensor Circuit "A" Circuit Open |
||
|
P0C5016 |
Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Below Threshold |
||
|
P0C5017 |
Drive Motor "A" Position Sensor Circuit "A" Circuit Voltage Above Threshold |
||
|
P0C5A13 |
Drive Motor "A" Position Sensor Circuit "B" Circuit Open |
||
|
P0C5A16 |
Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Below Threshold |
||
|
P0C5A17 |
Drive Motor "A" Position Sensor Circuit "B" Circuit Voltage Above Threshold |
||
|
Motor resolver ECU malfunction |
P1C621F |
Generator Control Module Offset Power Circuit Intermittent |
|
|
P1CB038 |
Drive Motor "A" Position Sensor REF Signal Frequency Incorrect |
||
|
Motor ECU malfunction |
P06B01C |
Generator Control Module Position Sensor REF Power Source Circuit Voltage Out of Range |
|
|
P1CAD49 |
Drive Motor "A" Position Sensor Internal Electronic Failure |
||
(b) Turn the ignition switch off.
| B |
|
| C |
|
|
|
2. |
CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION) |
Click here
| NG |
|
|
|
3. |
CLEAR DTC |
Click here
|
|
4. |
CHECK ENGINE RACING |
Click here
| NG |
|
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
|
|
|
5. |
CHECK CREEP MOVEMENT |
Click here
| NG |
|
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
|
|
|
6. |
INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY |
(a) Check that the hybrid transaxle fluid level is not extremely low.
HINT:
Click here
(b) Drain the hybrid transaxle fluid.
HINT:
Click here
(c) Check that the hybrid transaxle fluid is not contaminated by foreign matter.
OK:
- The hybrid transaxle fluid level is not extremely low.
- No foreign matter in the hybrid transaxle fluid.
| OK |
|
REPLACE TRANSMISSION INPUT DAMPER ASSEMBLY
|
| NG |
|
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY AND TRANSMISSION INPUT DAMPER ASSEMBLY
|
|
7. |
CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION) |
Click here
| OK |
|
REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY
|
| NG |
|
REPAIR OR REPLACE ENGINE |
|
|