Last Modified: 07-31-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026POG |
Model Year Start: 2023 |
Model: Corolla |
Prod Date Range: [09/2022 -
] |
Title: CELLULAR COMMUNICATION: SAFETY CONNECT SYSTEM (for HV Model): B157213; Microphone Circuit Open; 2023 - 2025 MY Corolla Corolla HV [09/2022 - ] |
DTC
|
B157213
|
Microphone Circuit Open
|
DESCRIPTION
This DTC is stored when the DCM (telematics transceiver) detects a malfunction in the telephone microphone assembly circuit.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B157213
|
Microphone Circuit Open
|
Current at terminal MCVD is lower than the malfunction threshold for 10 seconds or more while the power switch is on (IG)
|
-
DCM (telematics transceiver)
-
Telephone microphone assembly LH
-
Harness or connector
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Safety Connect System.
Click here
PROCEDURE
(a) Turn the power switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the power switch on (IG) and wait for 10 seconds or more.
(d) Turn the Techstream on.
(e) Clear the DTCs.
Body Electrical > Telematics > Clear DTCs
(f) Check for DTCs and check that no DTCs are output.
Body Electrical > Telematics > Trouble Codes
OK:
No DTCs are output.
NG
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - TELEPHONE MICROPHONE ASSEMBLY LH)
|
(a) Disconnect the I143 telematics transceiver connector.
(b) Disconnect the T24 telephone microphone assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
I143-5 (MCVD) - T24-1 (MAC1)
|
Always
|
Below 1 Ω
|
I143-6 (MCI+) - T24-2 (MO1+)
|
Always
|
Below 1 Ω
|
I143-7 (MCI-) - T24-4 (MO1-)
|
Always
|
Below 1 Ω
|
I143-23 (SGND) - Body ground
|
Always
|
10 kΩ or higher
|
I143-5 (MCVD) or T24-1 (MAC1) - Body ground
|
Always
|
10 kΩ or higher
|
I143-6 (MCI+) or T24-2 (MO1+) - Body ground
|
Always
|
10 kΩ or higher
|
I143-7 (MCI-) or T24-4 (MO1-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
CHECK DCM (TELEMATICS TRANSCEIVER) (TELEPHONE MICROPHONE ASSEMBLY LH POWER SOURCE)
|
(a) Remove the telephone microphone assembly LH but do not disconnect the connectors.
Click here
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
T24-1 (MAC1) - Body ground
|
Power switch on (IG)
|
7.5 to 8.5 V
|
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
T24-4 (MO1-) - Body ground
|
Always
|
Below 1 Ω
|
|
|
*a
|
Component with harness connected
(Telephone Microphone Assembly LH)
|
|
|
NG
|
|
|
4.
|
REPLACE DCM (TELEMATICS TRANSCEIVER)
|
(a) Replace the DCM (telematics transceiver) with a new one.
Click here
NOTICE:
-
The power switch must be off.
-
Do not exchange the DCM (telematics transceiver) with one from another vehicle.
|