Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026PGI |
Model Year Start: 2023 |
Model: Corolla |
Prod Date Range: [09/2022 -
] |
Title: TELEMATICS: TELEMATICS SYSTEM (for HV Model): Warning Notification Function Malfunction; 2023 - 2025 MY Corolla Corolla HV [09/2022 - ] |
Warning Notification Function Malfunction
|
PROCEDURE
1.
|
CHECK PROBLEM SYMPTOM (WARNING NOTIFICATION FUNCTION)
|
(a) Check the problem symptom.
(1) Check the problem symptom of the warning notification function.
Result
|
Proceed to
|
The multi-display screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning.
|
A
|
The multi-display screen shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning.
|
B
|
The multi-display screen shows a warning message different from the warning light or the multi-information display.
|
HINT:
-
The warning notification function sends information to the service center through communication.
-
Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.
A
|
|
|
(a) Check if the indicated warning light or message is listed in the following table.
HINT:
-
Only messages listed in the table are included in the warning notification function.
-
The warning names may differ from the items displayed on the multi-display.
Warning Name
|
Check engine warning
|
Hybrid control system warning
|
Brake system warning
|
ABS warning
|
VSC warning
|
ECB warning
|
Air suspension warning
|
KDSS warning
|
MTS warning
|
ARS warning
|
EPS warning
|
VGRS warning
|
Charging system warning
|
Airbag warning
|
PUH system warning
|
GOS warning
|
Brake override system warning
|
Smart system warning
|
Grille shutter warning
|
Automatic headlight beam level control system warning
|
AFS warning
|
LED headlight warning
|
AZB warning
|
Shift by wire warning
|
AT oil temp sensor warning
|
4WD warning
|
Tire pressure system warning
|
active stabilizer warning
|
Electric parking brake warning
|
Auto hold warning
|
Reversal control windshield wiper warning
|
Vehicle proximity notification warning
|
Stop and start system warning
|
Secondary collision brake warning
|
IPA system warning
|
Engine maintenance waring
|
GPF warning
|
Electric mirror system warning
|
IMT system warning
|
Auto park pilot warning
|
ASL warning
|
TBC warning
|
Multi weather light system warning
|
Secondary battery warning
|
Engine oil level warning
|
Brake fluid level warning
|
Engine oil pressure warning
|
Tire pressure low warning
|
Washer fluid level warning
|
Oil maintenance pre-warning
|
Oil maintenance demand warning
|
High coolant temperature warning
|
Battery diagnosis requirement
|
Battery diagnosis requirement output is being limited
|
Start prohibition notification
|
Hot water temp warning
|
Motor inverter hot temperature warning
|
Battery cooling fan maintenance warning
|
SLMD warning
|
Towing prohibited warning
|
Engine oil maintenance remainder warning
|
Forget to turn off the engine
|
ADS warning
|
Solar system warning
|
Integration system warning
|
Rear side radar warning
|
Parking support system warning
|
Driver monitor warning
|
Active front spoiler warning
|
TVD system warning
|
e-Latch system warning
|
Fingerprint authentication system warning
|
Power running board warning
|
PSD unit component replacement warning
|
Pedestrian protection device deployment
|
Face ID camera malfunction
|
GPF maintenance warning
|
Transmission system warning
|
Stabilizer disconnect mechanism malfunction
|
Result
|
Proceed to
|
Warning light or message is listed in the table.
|
A
|
Warning light or message is not listed in the table.
|
B
|
B |
|
END
|
A
|
|
|
3.
|
CHECK CAN COMMUNICATION SYSTEM
|
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Bus Check.
(e) Check that all ECUs and sensors that use CAN communication are connected.
Click here
Result
|
Proceed to
|
There are no connection problems.
|
A
|
There is a connection problem.
|
B
|
A
|
|
|
4.
|
CHECK METER WARNING LIGHT
|
(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.
OK:
There are no problems with warning lights or warning messages.
HINT:
The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.
Result
|
Proceed to
|
OK
|
A
|
NG
|
B
|
A
|
|
|
5.
|
CHECK AUDIO AND VISUAL SYSTEM
|
(a) Check if the audio and visual system is operating and functioning normally.
OK:
The audio and visual system is normal.
6.
|
CHECK METER WARNING LIGHT
|
(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.
OK:
There are no problems with warning lights or warning messages.
HINT:
The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.
|