- Back door opener
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000026ONB |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - 11/2022] |
| Title: SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY (for Hatchback): REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.
NOTICE:
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY](/t3Portal/stylegraphics/info.gif)
HINT:
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
-
for HV Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.
-
for Gasoline Model:
Learning completes when vehicle is driven
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Front Camera System (for TMC Made)
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
Learning completes when vehicle is operated normally
Effect/Inoperative Function When Necessary Procedures are not Performed
Necessary Procedures
Link
Power Door Lock Control System
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
PROCEDURE
1. PRECAUTION (w/ Pretensioner)
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
Click here
- Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
2. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
3. REMOVE REAR FLOOR MAT ASSEMBLY (w/o Deck Board)
Click here
4. REMOVE REAR DECK TRIM COVER (w/o Deck Board)
Click here
5. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)
Click here
6. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Pretensioner)
for M20A-FKS: Click here
CAUTION:
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
7. REMOVE REAR NO. 1 FLOOR BOARD (w/ Spare Tire)
Click here
8. REMOVE FRONT DECK FLOOR BOX (w/ Spare Tire)
Click here
9. REMOVE DECK FLOOR BOX LH (w/ Spare Tire)
Click here
10. REMOVE DECK FLOOR BOX RH (w/ Spare Tire)
Click here
11. REMOVE REAR DECK TRIM COVER (w/ Deck Board)
Click here
12. REMOVE REAR SEAT HEADREST ASSEMBLY
Click here
13. REMOVE REAR SEAT CENTER HEADREST ASSEMBLY (for RH Side)
Click here
14. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY
Click here
15. REMOVE REAR SEATBACK ASSEMBLY LH (for LH Side)
Click here
16. REMOVE REAR SEATBACK ASSEMBLY RH (for RH Side)
Click here
17. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
18. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
19. REMOVE REAR DOOR SCUFF PLATE
Click here
20. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
(a) Disconnect the rear door opening trim weatherstrip.
21. REMOVE REAR SEAT SIDE GARNISH
Click here
22. REMOVE DECK TRIM SIDE LOWER BOARD (w/ Spare Tire)
Click here
23. REMOVE CENTER FLOOR CROSSMEMBER BRACE SUB-ASSEMBLY (for GR)
Click here
24. REMOVE DECK TRIM SIDE PANEL ASSEMBLY
Click here
25. DISCONNECT REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY
|
(a) Remove the bolt to disconnect the floor anchor of the rear 3 point type seat outer belt assembly. |
|
26. REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (for RH Side)
for Bulb Type: Click here
for LED Type: Click here
27. REMOVE ROOF SIDE INNER GARNISH
Click here
28. REMOVE REAR 3 POINT TYPE SEAT OUTER BELT ASSEMBLY
|
(a) Loosen the bolt and disconnect the shoulder anchor of the rear 3 point type seat outer belt assembly. HINT: The bolt cannot be removed from the shoulder anchor of the rear 3 point type seat outer belt assembly. |
|
(b) w/o Pretensioner:
|
(1) Remove the 2 bolts. |
|
(2) Disengage the 2 guides to remove the rear 3 point type seat outer belt assembly.
(c) w/ Pretensioner:
|
(1) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector. HINT: Tape the screwdriver tip before use. |
|
|
(2) Remove the 2 bolts. |
|
(3) Disengage the 2 guides to remove the rear 3 point type seat outer belt assembly.
|
|