Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026MR3 |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: REAR AIRBAG SENSOR: REMOVAL; 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during side No. 2 airbag sensor removal/installation are shown below.
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Items for which learning is completed by driving the vehicle
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedures
|
Link
|
Pre-collision System (for TMMMS Made)
|
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.
|
|
Lane Tracing Assist System (for TMMMS Made)
|
Lane Departure Alert System (for TMMMS Made)
|
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
-
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
2. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
for M20A-FKS: Click here
for 2ZR-FAE: Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
3. REMOVE REAR SEAT HEADREST ASSEMBLY (w/ Removable Headrest)
Click here
4. DISCONNECT REAR SEAT CENTER LAP TYPE BELT ASSEMBLY
Click here
5. REMOVE REAR SEATBACK ASSEMBLY LH (for LH Side)
Click here
6. REMOVE REAR SEATBACK ASSEMBLY RH (for RH Side)
Click here
7. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
8. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
9. REMOVE REAR DOOR SCUFF PLATE
Click here
10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP
HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear seat side garnish.
11. REMOVE REAR SEAT SIDE GARNISH
w/o Rear Seat Side Airbag: Click here
w/ Rear Seat Side Airbag: Click here
12. REMOVE REAR SEAT AIRBAG ASSEMBLY (w/ Rear Seat Side Airbag)
Click here
13. REMOVE SIDE NO. 2 AIRBAG SENSOR
(a) Check that the ignition switch is off.
(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
(c) Disconnect the connector from the side No. 2 airbag sensor.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
*a
|
White Housing Lock
|
*b
|
Yellow CPA
|
|
Push in this Direction
|
|
Slide in this Direction
|
(2) Push down the white housing lock again and disconnect the connector.
NOTICE:
Do not push down the part (A) shown in the illustration when disconnecting the connector.
(d) Remove the bolt and disengage the claw to remove the side No. 2 airbag sensor.
|
|
(e) Check that the position of the white housing lock is as shown in the illustration.
|