Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026MKR |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CURTAIN SHIELD AIRBAG ASSEMBLY (for Hatchback): REMOVAL; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during curtain shield airbag assembly removal/installation are shown below.
HINT:
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Items for which learning is completed by driving the vehicle
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedures
|
Link
|
Front Camera System
|
-
Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more.*1
-
Drive the vehicle straight ahead at 15 km/h (9 mph) or more for 1 second or more.*2
|
|
Learning completes when vehicle is operated normally
Effect/Inoperative Function when Necessary Procedure not Performed
|
Necessary Procedures
|
Link
|
Power Door Lock Control System
|
Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch.
|
|
NOTICE:
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 3 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
-
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for Single Knob Type))
HINT:
-
Use the same procedure for the RH side and LH side.
-
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
2. REMOVE ROOF HEADLINING ASSEMBLY
Click here
3. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY
CAUTION:
When storing the curtain shield airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side
|
NOTICE:
When removing the curtain shield airbag assembly, have assistants hold it to prevent it from bending.
(a) Check that the engine switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 60 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Disconnect the airbag connector.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
HINT:
Refer to How to Connect or Disconnect Airbag Connector.
Click here
(d) Using a needle nose pliers No. 2 or equivalent, remove the 4 pins from the 3 clips (A) and clip (B).
NOTICE:
Do not damage the pins.
*1
|
Pin
|
-
|
-
|
*a
|
Clip (A)
|
*b
|
Clip (B)
|
*c
|
Clip (C)
|
*d
|
Needle Nose Pliers No. 2
|
*e
|
Thin Screwdriver
|
-
|
-
|
|
Remove in this Direction
|
-
|
-
|
(e) Using 2 thin screwdrivers, disengage the 2 claws of each clip (A) and (B), and separate the 3 clips (A) and clip (B) from the vehicle body as shown in the illustration.
HINT:
Separate the 3 clips (A), clip (B) and curtain shield airbag assembly from the vehicle body as a unit.
(f) Disengage the clip (C).
(g) While holding the curtain shield airbag assembly, remove the 7 bolts and curtain shield airbag assembly.
(h) Remove the 3 clips (A) and clip (B) from the curtain shield airbag assembly.
|