| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000026K8D |
| Model Year Start: 2023 | Model: GR Corolla | Prod Date Range: [09/2022 - ] |
| Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for 8 Inch Display Type (w/ Single Knob Type) or 10.5 Inch Display Type): B154711,B154713; GNSS Antenna Circuit Short to Ground; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] | ||
|
DTC |
B154711 |
GNSS Antenna Circuit Short to Ground |
|
DTC |
B154713 |
GNSS Antenna Circuit Open |
DESCRIPTION
These DTCs are stored when the radio and display receiver assembly detects an open or short in GNSS antenna assembly.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
DTC Output from |
Priority |
|---|---|---|---|---|---|
|
B154711 |
GNSS Antenna Circuit Short to Ground |
Short in GNSS antenna assembly (2 trip detection logic) |
|
Navigation System |
A |
|
B154713 |
GNSS Antenna Circuit Open |
Open in GNSS antenna assembly (2 trip detection logic) |
|
Navigation System |
A |
- *1: for Sedan Model
- *2: for Hatchback Model
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed.
Click here
![2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM (for 8 Inch Display Type (w/ Single Knob Type) or 10.5 Inch Display Type): PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
INSPECT NAVIGATION ANTENNA ASSEMBLY |
Click here
| NG |
|
REPLACE NAVIGATION ANTENNA ASSEMBLY
|
|
|
2. |
CHECK MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for Hatchback Model |
A |
|
for Sedan Model |
B |
| B |
|
|
|
3. |
INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY |
|
(a) Disconnect the navigation antenna assembly connector. |
|
|
(b) Disconnect the radio and display receiver assembly connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D-3 - A-1 |
Always |
Below 1 Ω |
|
D-3a - A-1a |
Always |
Below 1 Ω |
|
D-3a or A-1a - Body ground |
Always |
10 kΩ or higher |
| OK |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG |
|
REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY
|
|
4. |
INSPECT ANTENNA CORD SUB-ASSEMBLY |
|
(a) Disconnect the navigation antenna assembly connector. |
|
|
(b) Disconnect the radio and display receiver assembly connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D-3 - A-1 |
Always |
Below 1 Ω |
|
D-3a - A-1a |
Always |
Below 1 Ω |
|
D-3a or A-1a - Body ground |
Always |
10 kΩ or higher |
| OK |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
| NG |
|
REPLACE ANTENNA CORD SUB-ASSEMBLY
|
|
|