Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026JZL |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 - 11/2022] |
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model except TMC Made): TERMINALS OF ECU; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022] |
TERMINALS OF ECU
HINT:
-
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click here
-
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
-
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR
(a) Check the No. 1 CAN junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 1 CAN Junction Connector)
|
*b
|
to Central Gateway ECU (Network Gateway ECU)
|
*c
|
to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
|
*d
|
to Forward Recognition Camera
(w/ Toyota Safety Sense)
|
*e
|
to Central Gateway ECU (Network Gateway ECU)
(w/o Blind Spot Monitor System)
|
*f
|
to No. 7 CAN Junction Connector
(w/ Blind Spot Monitor System)
|
(2) Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
I91-1 (CANH)
|
G
|
Central gateway ECU (network gateway ECU)
(for Bus 1)
|
I91-7 (CANL)
|
SB
|
I91-4 (CANH)
|
P
|
Millimeter wave radar sensor assembly*1
(for Bus 1)
|
I91-10 (CANL)
|
W
|
I91-5 (CANH)
|
W
|
Forward recognition camera*1
(for Bus 1)
|
I91-11 (CANL)
|
B
|
I91-6 (CANH)
|
R
|
Central gateway ECU (network gateway ECU)*2
(for Bus 1)
|
I91-12 (CANL)
|
W
|
I91-6 (CANH)
|
R
|
No. 7 CAN junction connector*3
(for Bus 1)
|
I91-12 (CANL)
|
W
|
-
*1: w/ Toyota Safety Sense
-
*2: w/o Blind Spot Monitor System
-
*3: for Sedan with Blind Spot Monitor System
NO. 3 CAN JUNCTION CONNECTOR (w/ Smart Key System)
(a) Check the No. 3 CAN junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 3 CAN Junction Connector)
|
*b
|
to Combination Meter Assembly
|
*c
|
to Main Body ECU (Multiplex Network Body ECU)
|
*d
|
to Air Conditioning Amplifier Assembly
|
*e
|
to Certification ECU (Smart Key ECU Assembly)
|
*f
|
to Central gateway ECU (network gateway ECU)
|
(2) Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
I94-1 (CANH)
|
L
|
Combination meter assembly
(for Bus 5)
|
I94-11 (CANL)
|
W
|
I94-2 (CANH)
|
B
|
Main body ECU (multiplex network body ECU)
(for Bus 5)
|
I94-12 (CANL)
|
W
|
I94-4 (CANH)
|
G
|
Air conditioning amplifier assembly
(for Bus 5)
|
I94-14 (CANL)
|
W
|
I94-5 (CANH)
|
Y
|
Certification ECU (smart key ECU assembly)
(for Bus 5)
|
I94-15 (CANL)
|
W
|
I94-6 (CANH)
|
L
|
Central gateway ECU (network gateway ECU)
(for Bus 5)
|
I94-16 (CANL)
|
W
|
NO. 3 CAN JUNCTION CONNECTOR (w/o Smart Key System)
(a) Check the No. 3 CAN junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 3 CAN Junction Connector)
|
*b
|
to Combination Meter Assembly
|
*c
|
to Main Body ECU (Multiplex Network Body ECU)
|
*d
|
to Air Conditioning Amplifier Assembly
|
*e
|
to Central gateway ECU (network gateway ECU)
|
-
|
-
|
(2) Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
I125-2 (CANH)
|
L
|
Combination meter assembly
(for Bus 5)
|
I125-13 (CANL)
|
W
|
I125-3 (CANH)
|
B
|
Main body ECU (multiplex network body ECU)
(for Bus 5)
|
I125-14 (CANL)
|
W
|
I125-5 (CANH)
|
G
|
Air conditioning amplifier assembly
(for Bus 5)
|
I125-16 (CANL)
|
W
|
I125-7 (CANH)
|
L
|
Central gateway ECU (network gateway ECU)
(for Bus 5)
|
I125-18 (CANL)
|
W
|
NO. 4 CAN JUNCTION CONNECTOR
(a) Check the No. 4 CAN junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 4 CAN Junction Connector)
|
*b
|
to Steering Sensor
|
*c
|
to Airbag Sensor Assembly
|
*d
|
to No. 1 Junction Connector
|
*e
|
to Power Steering ECU with Motor Assembly
|
*f
|
to Brake Actuator Assembly
|
*g
|
to Central Gateway ECU (Network Gateway ECU)
|
*h
|
to ECM
|
*i
|
to TCM
(for CVT (K120))
|
-
|
-
|
(2) Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
I95-1 (CANH)
|
B
|
Steering sensor
(for Bus 4)
|
I95-12 (CANL)
|
W
|
I95-3 (CANH)
|
R
|
Airbag sensor assembly
(for Bus 4)
|
I95-14 (CANL)
|
G
|
I95-4 (CANH)
|
P
|
No. 1 junction connector
(for Bus 4)
|
I95-15 (CANL)
|
W
|
I95-5 (CANH)
|
G
|
Power steering ECU with motor assembly
(for Bus 4)
|
I95-16 (CANL)
|
W
|
I95-6 (CANH)
|
B
|
Brake actuator assembly
(for Bus 4)
|
I95-17 (CANL)
|
W
|
I95-9 (CANH)
|
P
|
Central gateway ECU (network gateway ECU)
(for Bus 2)
|
I95-20 (CANL)
|
W
|
I95-10 (CANH)
|
LG
|
ECM
(for Bus 2)
|
I95-21 (CANL)
|
W
|
I95-11 (CANH)
|
G
|
TCM*
(for Bus 2)
|
I95-22 (CANL)
|
W
|
NO. 6 CAN JUNCTION CONNECTOR
(a) Check the No. 6 CAN junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 6 CAN Junction Connector)
|
*b
|
to Central Gateway ECU (Network Gateway ECU)
|
*c
|
to DCM (Telematics Transceiver)
(w/ Telematics Transceiver)
|
*d
|
to Radio and Display Receiver Assembly
|
(2) Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
I132-1 (CANH)
|
L
|
Central gateway ECU (network gateway ECU)
(for Bus 3)
|
I132-12 (CANL)
|
R
|
I132-2 (CANH)
|
G
|
Central gateway ECU (network gateway ECU)
(for Bus 3)
|
I132-13 (CANL)
|
W
|
I132-3 (CANH)
|
L
|
DCM (telematics transceiver)*
(for Bus 3)
|
I132-14 (CANL)
|
W
|
I132-4 (CANH)
|
B
|
Radio and display receiver assembly
(for Bus 3)
|
I132-15 (CANL)
|
W
|
-
*: w/ Telematics Transceiver
NO. 7 CAN JUNCTION CONNECTOR (w/ Blind Spot Monitor System)
(a) Check the No. 7 CAN junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 7 CAN Junction Connector)
|
*b
|
to Blind Spot Monitor Sensor LH
|
*c
|
to No. 1 CAN Junction Connector
|
*d
|
to CAN Junction Terminal
|
(2) Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
O121-1 (CANH)
|
G
|
Blind spot monitor sensor LH
(for Bus 1)
|
O121-12 (CANL)
|
W
|
O121-2 (CANH)
|
R
|
No. 1 CAN junction connector
(for Bus 1)
|
O121-13 (CANL)
|
W
|
O121-3 (CANH)
|
B
|
CAN junction terminal
(for Bus 1)
|
O121-14 (CANL)
|
W
|
NO. 1 JUNCTION CONNECTOR
(a) Check the No. 1 junction connector.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to No. 1 Junction Connector)
|
*b
|
to Central Gateway ECU (Network Gateway ECU)
|
*c
|
to Occupant Detection ECU
|
*d
|
to No. 4 CAN Junction Connector
|
(2) Check the connection diagram of the components which are connected to the No. 1 junction connector.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
O118-9 (CANH)
|
B
|
Central gateway ECU (network gateway ECU)
(for Bus 4)
|
O118-20 (CANL)
|
W
|
O118-10 (CANH)
|
LG
|
Occupant detection ECU
(for Bus 4)
|
O118-21 (CANL)
|
W
|
O118-11 (CANH)
|
P
|
No. 4 CAN junction connector
(for Bus 4)
|
O118-22 (CANL)
|
W
|
CAN JUNCTION TERMINAL (w/ Blind Spot Monitor System)
(a) Check the CAN junction terminal.
(1) Connection diagram
*a
|
Front view of wire harness connector
(to CAN Junction Terminal)
|
*b
|
to No. 7 CAN Junction Connector
|
(2) Check the connection diagram of the components which are connected to the CAN junction terminal.
Terminal No. (Symbol)
|
Wiring Color
|
Connected to
|
O95-3 (CANH)
|
B
|
No. 7 CAN junction connector
(for Bus 1)
|
O95-2 (CANL)
|
W
|
DLC3
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I26-6 (CANH) - I26-14 (CANL)
|
R - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I26-6 (CANH) - I26-4 (CG)
|
R - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I26-14 (CANL) - I26-4 (CG)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I26-6 (CANH) - I26-16 (BAT)
|
R - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I26-14 (CANL) - I26-16 (BAT)
|
W - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
*a
|
Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
|
-
|
-
|
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I53 central gateway ECU (network gateway ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
|
-
|
-
|
Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-14 (CA6H) - I53-5 (CA6L)
|
R - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
1 MΩ or higher
|
I53-14 (CA6H) - I53-10 (GND)
|
R - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-5 (CA6L) - I53-10 (GND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-14 (CA6H) - I53-1 (BATT)
|
R - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-5 (CA6L) - I53-1 (BATT)
|
W - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
Bus 1 Main Lines (w/ Blind Spot Monitor System)
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-23 (CA1H) - I53-8 (CA1L)
|
G - SB
|
HIGH-level CAN bus line - HIGH-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
I53-23 (CA1H) - I53-10 (GND)
|
G - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-8 (CA1L) - I53-10 (GND)
|
SB - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-23 (CA1H) - I53-1 (BATT)
|
G - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-8 (CA1L) - I53-1 (BATT)
|
SB - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
Bus 1 Main Lines (w/o Blind Spot Monitor System)
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-23 (CA1H) - I53-9 (CAXH)
|
G - R
|
HIGH-level CAN bus line - HIGH-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
I53-8 (CA1L) - I53-24 (CAXL)
|
SB - W
|
LOW-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
I53-23 (CA1H) - I53-10 (GND)
|
G - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-8 (CA1L) - I53-10 (GND)
|
SB - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-23 (CA1H) - I53-1 (BATT)
|
G - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-8 (CA1L) - I53-1 (BATT)
|
SB - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
Bus 2 Main Lines
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-18 (CA4H) - I53-17 (CA4L)
|
P - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
I53-18 (CA4H) - I53-10 (GND)
|
P - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-17 (CA4L) - I53-10 (GND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-18 (CA4H) - I53-1 (BATT)
|
P - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-17 (CA4L) - I53-1 (BATT)
|
W - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
Bus 3 Main Lines
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-6 (CA3H) - I53-19 (CAYH)
|
G - L
|
HIGH-level CAN bus line - HIGH-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
I53-21 (CA3L) - I53-20 (CAYL)
|
W - R
|
LOW-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
Below 1 Ω
|
I53-6 (CA3H) - I53-10 (GND)
|
G - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-21 (CA3L) - I53-10 (GND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-6 (CA3H) - I53-1 (BATT)
|
G - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-21 (CA3L) - I53-1 (BATT)
|
W - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
Bus 4 Main Lines
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-22 (CA2H) - I53-7 (CA2L)
|
B - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
I53-22 (CA2H) - I53-10 (GND)
|
B - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-7 (CA2L) - I53-10 (GND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-22 (CA2H) - I53-1 (BATT)
|
B - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-7 (CA2L) - I53-1 (BATT)
|
W - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
Bus 5 Main Lines
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I53-15 (CA5H) - I53-16 (CA5L)
|
L - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
I53-15 (CA5H) - I53-10 (GND)
|
L - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-16 (CA5L) - I53-10 (GND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I53-15 (CA5H) - I53-1 (BATT)
|
L - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I53-16 (CA5L) - I53-1 (BATT)
|
W - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
STEERING SENSOR
*a
|
Component without harness connected
(Steering Sensor)
|
-
|
-
|
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I46 steering sensor connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Steering Sensor)
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I46-3 (CANH) - I46-8 (CANL)
|
B - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I46-3 (CANH) - I46-6 (ESS)
|
B - LA
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I46-8 (CANL) - I46-6 (ESS)
|
W - LA
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I46-3 (CANH) - I46-4 (BAT)
|
B - LA-Y
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I46-8 (CANL) - I46-4 (BAT)
|
W - LA-Y
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
ECM (for M20A-FKS)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A47 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to ECM)
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
A47-8 (CANH) - A47-18 (CANL)
|
GR - BR
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
A47-8 (CANH) - A47-10 (E1)
|
GR - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A47-18 (CANL) - A47-10 (E1)
|
BR - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A47-8 (CANH) - A47-1 (BATT)
|
GR - G
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
A47-18 (CANL) - A47-1 (BATT)
|
BR - G
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
ECM (for 2ZR-FAE)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A46 and C77 ECM connectors.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to ECM)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
A46-13 (CANH) - A46-26 (CANL)
|
GR - BR
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
A46-13 (CANH) - C77-59 (E1)
|
GR - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A46-26 (CANL) - C77-59 (E1)
|
BR - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A46-13 (CANH) - A46-1 (BATT)
|
GR - P
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
A46-26 (CANL) - A46-1 (BATT)
|
BR - P
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
BRAKE ACTUATOR ASSEMBLY (w/ Electric Parking Brake System)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A51 brake actuator assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Brake Actuator Assembly)
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
A51-5 (CANH) - A51-19 (CANL)
|
R - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
A51-5 (CANH) - A51-46 (GND1)
|
R - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A51-19 (CANL) - A51-46 (GND1)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A51-5 (CANH) - A51-30 (+BS)
|
R - W
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
A51-19 (CANL) - A51-30 (+BS)
|
W - W
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
BRAKE ACTUATOR ASSEMBLY (w/o Electric Parking Brake System)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A100 brake actuator assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Brake Actuator Assembly)
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
A100-26 (CANH) - A100-14 (CANL)
|
R - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
A100-26 (CANH) - A100-38 (GND1)
|
R - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A100-14 (CANL) - A100-38 (GND1)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A100-26 (CANH) - A100-25 (+BS)
|
R - W
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
A100-14 (CANL) - A100-25 (+BS)
|
W - W
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
POWER STEERING ECU WITH MOTOR ASSEMBLY
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I21 and I42 power steering ECU with motor assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Power Steering ECU with Motor Assembly)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I21-7 (CANH) - I21-8 (CANL)
|
G - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I21-7 (CANH) - I42-2 (PGND)
|
G - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I21-8 (CANL) - I42-2 (PGND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I21-7 (CANH) - I42-1 (PIG)
|
G - W
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I21-8 (CANL) - I42-1 (PIG)
|
W - W
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I4 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Combination Meter Assembly)
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I4-9 (CANH) - I4-25 (CANL)
|
L - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
I4-9 (CANH) - I4-23 (ES)
|
L - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I4-25 (CANL) - I4-23 (ES)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I4-9 (CANH) - I4-22 (B)
|
L - G
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I4-25 (CANL) - I4-22 (B)
|
W - G
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I85 main body ECU (multiplex network body ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I85-5 (CANH) - I85-4 (CANL)
|
B - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I85-5 (CANH) - I26-4 (CG)
|
B - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I85-4 (CANL) - I26-4 (CG)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I85-5 (CANH) - I26-16 (BAT)
|
B - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I85-4 (CANL) - I26-16 (BAT)
|
W - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Key System)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I1 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I1-1 (CANH) - I1-2 (CANL)
|
Y - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I1-1 (CANH) - I1-18 (E)
|
Y - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I1-2 (CANL) - I1-18 (E)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I1-1 (CANH) - I1-3 (+B)
|
Y - GR
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I1-2 (CANL) - I1-3 (+B)
|
W - GR
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
AIRBAG SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I47 airbag sensor assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Airbag Sensor Assembly)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I47-26 (CANH) - I47-27 (CANL)
|
R - G
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
108 to 132 Ω
|
I47-26 (CANH) - I47-33 (E1)
|
R - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I47-27 (CANL) - I47-33 (E1)
|
G - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I47-26 (CANH) - I26-16 (BAT)
|
R - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I47-27 (CANL) - I26-16 (BAT)
|
G - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I49 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I49-2 (CANH) - I49-1 (CANL)
|
G - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I49-2 (CANH) - I49-17 (GND)
|
G - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I49-1 (CANL) - I49-17 (GND)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I49-2 (CANH) - I49-5 (B)
|
G - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I49-1 (CANL) - I49-5 (B)
|
W - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
RADIO AND DISPLAY RECEIVER ASSEMBLY
Refer to Terminals of ECU.
-
for Audio and Visual System
Click here
-
for Navigation System
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I56 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Radio and Display Receiver Assembly)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I56-13 (CANH) - I56-14 (CANL)
|
B - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I56-13 (CANH) - I26-4 (CG)
|
B - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I56-14 (CANL) - I26-4 (CG)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I56-13 (CANH) - I26-16 (BAT)
|
B - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I56-14 (CANL) - I26-16 (BAT)
|
W - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the T9 forward recognition camera connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Forward Recognition Camera)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
T9-5 (CA1P) - T9-11 (CA1N)
|
W - B
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
T9-5 (CA1P) - T9-10 (GND)
|
W - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
T9-11 (CA1N) - T9-10 (GND)
|
B - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
T9-5 (CA1P) - I26-16 (BAT)
|
W - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
T9-11 (CA1N) - I26-16 (BAT)
|
B - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the A1 millimeter wave radar sensor assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
A1-3 (CA2H) - A1-2 (CA2L)
|
W - B
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
A1-3 (CA2H) - A1-1 (SGND)
|
W - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A1-2 (CA2L) - A1-1 (SGND)
|
B - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
A1-3 (CA2H) - I26-16 (BAT)
|
W - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
A1-2 (CA2L) - I26-16 (BAT)
|
B - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
OCCUPANT DETECTION ECU
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the j4 occupant detection ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Occupant Detection ECU)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
j4-5 (CANH) - j4-4 (CANL)
|
R - SB
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
j4-5 (CANH) - j4-10 (GND)
|
R - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
j4-4 (CANL) - j4-10 (GND)
|
SB - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
j4-5 (CANH) - I26-16 (BAT)
|
R - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
j4-4 (CANL) - I26-16 (BAT)
|
SB - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
DCM (TELEMATICS TRANSCEIVER) (w/ Telematics Transceiver)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I143 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to DCM (Telematics Transceiver))
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
I143-25 (CANP) - I143-26 (CANN)
|
L - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
I143-25 (CANP) - I143-20 (E)
|
L - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I143-26 (CANN) - I143-20 (E)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
I143-25 (CANP) - I143-1 (+B)
|
L - SB
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
I143-26 (CANN) - I143-1 (+B)
|
W - SB
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the O57 blind spot monitor sensor LH connector.
(c) Measure the resistance according to the value(s) in the table below.
*1
|
DLC3
|
-
|
-
|
*a
|
Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
O57-2 (CA1P) - O57-7 (CA1N)
|
G - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
O57-2 (CA1P) - O57-10 (BLGD)
|
G - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
O57-7 (CA1N) - O57-10 (BLGD)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
O57-2 (CA1P) - I26-16 (BAT)
|
G - LG
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
O57-7 (CA1N) - I26-16 (BAT)
|
W - LG
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
TCM (for CVT (K120))
Refer to Terminals of ECU.
Click here
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the C80 TCM connector.
(c) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of wire harness connector
(to TCM)
|
-
|
-
|
Standard Resistance:
Terminal No. (Symbol)
|
Wiring Color
|
Terminal Description
|
Condition
|
Specified Condition
|
C80-15 (CANH) - C80-16 (CANL)
|
Y - W
|
HIGH-level CAN bus line - LOW-level CAN bus line
|
Cable disconnected from negative (-) battery terminal
|
54 to 69 Ω
|
C80-15 (CANH) - C80-2 (E1)
|
Y - W-B
|
HIGH-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
C80-16 (CANL) - C80-2 (E1)
|
W - W-B
|
LOW-level CAN bus line - Ground
|
Cable disconnected from negative (-) battery terminal
|
200 Ω or higher
|
C80-15 (CANH) - C80-1 (+B)
|
Y - R
|
HIGH-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
C80-16 (CANL) - C80-1 (+B)
|
W - R
|
LOW-level CAN bus line - Battery positive (+)
|
Cable disconnected from negative (-) battery terminal
|
6 kΩ or higher
|
|