- DTC judgment completed
- System normal
| Last Modified: 07-31-2024 | 6.11:8.1.0 | Doc ID: RM1000000026FLS |
| Model Year Start: 2023 | Model: Corolla Hatchback | Prod Date Range: [09/2022 - ] |
| Title: K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: P274512,P274514,P274531; Intermediate Shaft Speed Sensor "B" Circuit Short to Battery; 2023 - 2025 MY Corolla Corolla Hatchback [09/2022 - ] | ||
|
DTC |
P274512 |
Intermediate Shaft Speed Sensor "B" Circuit Short to Battery |
|
DTC |
P274514 |
Intermediate Shaft Speed Sensor "B" Circuit Short to Ground or Open |
|
DTC |
P274531 |
Intermediate Shaft Speed Sensor "B" No Signal |
DESCRIPTION
The transmission revolution sensor (NC1) detects the intermediate shaft (C1 clutch) speed and sends it to the TCM.
The TCM determines if gear mode should be entered by comparing the transmission revolution sensor (NT) and (NC1) signals.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P274512 |
Intermediate Shaft Speed Sensor "B" Circuit Short to Battery |
The transmission revolution sensor (NC1) signal is normal but the transmission revolution sensor (NC1) output voltage is higher than 1.8 V for 4.5 seconds or more (1-trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P07C8 |
|
P274514 |
Intermediate Shaft Speed Sensor "B" Circuit Short to Ground or Open |
The transmission revolution sensor (NC1) signal is normal but the transmission revolution sensor (NC1) output voltage is less than 0.2 V for 4.5 seconds or more (1-trip detection logic) |
|
Comes on |
DTC stored |
SAE Code: P07C7 |
|
P274531 |
Intermediate Shaft Speed Sensor "B" No Signal |
When the transmission revolution sensor (NOUT) signal indicates 300 rpm or more and the SPD signal indicates 10 km/h (6 mph) or more, transmission revolution sensor (NC1) signal indicates less than 300 rpm for 5 seconds or more (1-trip detection logic). |
|
Comes on |
DTC stored |
SAE Code: P2747 |
MONITOR DESCRIPTION
The TCM receives signals from the transmission revolution sensor (NC1) installed to the continuously variable transaxle and determines the intermediate shaft (C1 clutch) speed.
If the TCM detects no signal from the transmission revolution sensor (NC1) even while the vehicle is being driven, it will determine that in the transmission revolution sensor (NC1) is malfunctioning, illuminate the MIL and store a DTC.
MONITOR STRATEGY
|
Related DTCs |
P07C7: Intermediate shaft speed sensor (for Gear Drive) (Transmission revolution sensor (NC1))/Range check (Low voltage) P07C8: Intermediate shaft speed sensor (for Gear Drive) (Transmission revolution sensor (NC1))/Range check (High voltage) P2747: Intermediate shaft speed sensor (for Gear Drive) (Transmission revolution sensor (NC1))/Verify pulse input |
|
Required sensors/Components |
Transmission revolution sensor (NC1) Transmission revolution sensor (NOUT) Vehicle speed sensor |
|
Frequency of operation |
Continuous |
|
Duration |
P2747: 5 sec. P07C7, P07C8: 4.5 sec. |
|
MIL operation |
Immediate |
|
Sequence of operation |
None |
TYPICAL ENABLING CONDITIONS
All
|
Battery voltage |
8 V or more |
|
Engine switch |
On (IG) |
|
Starter |
OFF |
P07C7, P07C8
|
Intermediate shaft speed sensor pulse input fail (P2747) (Pending / MIL) |
Not detected |
P2747
|
Intermediate shaft speed sensor range check fail (P07C7, P07C8) (Pending / MIL) |
Not detected |
|
D range position switch |
ON |
|
R range position switch |
OFF |
|
Park position switch |
OFF |
|
Neutral position switch |
OFF |
|
Engine |
Running |
|
Pressure control solenoid circuit fail (P08CA, P08CB, P0962, P0963, P0966, P0967, P2826, P2827, P282F, P2830) (Pending + MIL) |
Not detected |
|
Torque converter clutch pressure control solenoid circuit fail (P2763, P2764) (Pending + MIL) |
Not detected |
|
Output speed sensor revolution |
300 rpm or more |
|
Vehicle speed |
10 km/h (6.22 mph) or more |
One of the following conditions is met: Condition (A), (B) or (C)
-
Condition (A)
ECT
20°C (68°F) or more
ECT sensor circuit fail (P0117, P0118)
(Pending + MIL)
Not detected
All of the following conditions are met
2 sec. or more
- Park position switch
OFF
- Neutral position switch
OFF
Condition (B)
One of the following conditions is met
-
- ECT
Less than 20°C (68°F)
- ECT sensor circuit fail (P0117, P0118)
(Pending + MIL)
Detected
All of the following conditions are met
30 sec. or more
- Park position switch
OFF
- Neutral position switch
OFF
Condition (C)
Speed sensor monitor driving mode
Belt mode (Synchronizer engaged)
Synchronizer
Engaged
TYPICAL MALFUNCTION THRESHOLDS
P07C7
|
Intermediate shaft speed sensor voltage |
Less than 0.2 V |
P07C8
|
Intermediate shaft speed sensor voltage |
More than 1.8 V |
P2747
|
Intermediate shaft speed sensor revolution |
Less than 300 rpm |
COMPONENT OPERATING RANGE
P07C7, P07C8
|
Intermediate shaft speed sensor voltage |
0.2 V or more and 1.8 V or less |
P2747
|
Intermediate shaft speed sensor revolution |
300 rpm or more |
CONFIRMATION DRIVING PATTERN
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT:
- After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
-
When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.
Click here
![2023 MY Corolla Corolla Hatchback [09/2022 - 11/2022]; K120 / K121 (CVT): K120 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG) and turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for 2 minutes or more.
- Turn the engine switch on (IG) and turn the Techstream on.
- Start the engine.
-
Perform the D Position Shift Test inspection in Road Test. [*1]
Click here
HINT:
[*1]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- Stop the vehicle.
- Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
- Input the DTC: P274512, P274514 or P274531.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
N/A
- Unable to perform DTC judgment
- Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
HINT:
- If the judgment result shows NORMAL, the system is normal.
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
-
Strictly observe posted speed limits, traffic laws and road conditions.
- Do not drive the vehicle with the cable of the Techstream contacting the pedals, shift lever or steering wheel.
- Driving the vehicle with the cable of the Techstream contacting these areas could impede vehicle control, resulting in a serious accident.
-
Do not operate the Techstream while driving the vehicle.
- Operating the Techstream while driving the vehicle will prevent you from paying sufficient attention to vehicle surroundings, and could result in a serious accident.
NOTICE:
-
Perform the universal trip to clear permanent DTCs.
Click here
-
Perform registration and/or initialization when parts related to the continuously variable transaxle system are replaced.
Click here
-
Check that no DTCs are stored after performing initialization.
Click here
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (NC1 SENSOR SPEED AND NC1 SENSOR VOLTAGE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Transmission / Data List.
(e) According to the display on the Techstream, read the Data List.
Powertrain > Transmission > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
NC1 Sensor Speed |
Intermediate shaft (C1 clutch) speed (NC1) |
Min.: 0 rpm Max.: 65535 rpm |
|
- |
|
NC1 Sensor Voltage |
Transmission revolution sensor (NC1) output voltage |
Min.: 0.000 V Max.: 4.999 V |
0.2 to 1.8 V: Engine idling (Vehicle stopped with shift lever in P or N) |
- |
Powertrain > Transmission > Data List
|
Tester Display |
|---|
|
NC1 Sensor Speed |
|
NC1 Sensor Voltage |
|
Result |
Proceed to |
|---|---|
|
Data List values are normal |
A |
|
Data List values are not normal |
B |
| B |
|
|
|
2. |
REPLACE TCM |
(a) Replace the TCM.
Click here
| NEXT |
|
PERFORM REGISTRATION AND INITIALIZATION for Registration: Click here
for Initialization: Click here
|
|
3. |
CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) |
(a) Disconnect the C61 transmission wire connector.
(b) Disconnect the C80 TCM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C61-16 (NC1B) - C80-24 (NC1B) |
Always |
Below 1 Ω |
|
C61-17 (NC1O) - C80-8 (NC1O) |
Always |
Below 1 Ω |
|
C80-2 (E1) - Body ground |
Always |
Below 1 Ω |
|
C61-16 (NC1B) or C80-24 (NC1B) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
C61-17 (NC1O) or C80-8 (NC1O) - Body ground and other terminals |
Always |
10 kΩ or higher |
(d) Connect the C80 TCM connector.
(e) Connect the C61 transmission wire connector.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - TCM) |
|
|
4. |
CHECK TCM |
|
(a) Disconnect the C61 transmission wire connector. |
|
(b) Turn the engine switch on (IG).
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C61-16 (NC1B) - Body ground |
Engine switch on (IG) |
11 to 14 V |
(d) Turn the engine switch off.
(e) Connect the C61 transmission wire connector.
(f) Disconnect the C80 TCM connector.
|
*a |
Component without harness connected (TCM) |
- |
- |
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
8 (NC1O) - 2 (E1) |
Always |
99 to 101 Ω |
(h) Connect the C80 TCM connector.
| NG |
|
|
|
5. |
INSPECT TRANSMISSION WIRE |
(a) Disconnect the C61 transmission wire connector.
|
(b) Disconnect the transmission wire connector from the transmission revolution sensor (NC1). Click here
|
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 (transmission revolution sensor side) - 16 (NC1B) (wire harness connector side) |
Always |
Below 1 Ω |
|
2 (transmission revolution sensor side) - 17 (NC1O) (wire harness connector side) |
Always |
Below 1 Ω |
|
1 (transmission revolution sensor side) or 16 (NC1B) (wire harness connector side) - All other terminals |
Always |
10 kΩ or higher |
|
2 (transmission revolution sensor side) or 17 (NC1O) (wire harness connector side) - All other terminals |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPLACE TRANSMISSION WIRE
|
|
6. |
REPLACE TCM |
(a) Replace the TCM.
Click here
| NEXT |
|
PERFORM REGISTRATION AND INITIALIZATION for Registration: Click here
for Initialization: Click here
|
|
|