Last Modified: 05-13-2024 6.11:8.1.0 Doc ID: RM1000000026EN5
Model Year Start: 2023 Model: GR Corolla Prod Date Range: [09/2022 - 11/2022]
Title: NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model TMC Made): Certification ECU Communication Stop Mode; 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]

Certification ECU Communication Stop Mode

DESCRIPTION

Detection Item

Symptom

Trouble Area

Certification ECU Communication Stop Mode

Communication stop for "Certification (Smart)" and/or "Power Management" is indicated on the "Communication Bus Check" screen of the GTS.

Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model TMC Made): DIAGNOSIS SYSTEM

  • Certification ECU (smart key ECU assembly) branch line or connector
  • Power source circuit of certification ECU (smart key ECU assembly)
  • Certification ECU (smart key ECU assembly) ground circuit
  • Certification ECU (smart key ECU assembly)

WIRING DIAGRAM

except G16E-GTS
for G16E-GTS

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

NOTICE:

  • Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model TMC Made): HOW TO PROCEED WITH TROUBLESHOOTING

  • Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
  • After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

    Click here 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 -        ]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: BEFORE DISCONNECTING BATTERY

  • When disconnecting and reconnecting the battery.

    HINT:

    When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL: AUTOMATIC LEARNING CHART

  • Some parts must be initialized and set when replacing or removing and installing parts.

    Click here 2023 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - 11/2022]; SETUP: WHEN REPLACING OR REMOVING/INSTALLING PARTS: WORK PROCEDURE

  • After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

    DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

  • After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; NETWORKING: CAN COMMUNICATION SYSTEM (for Gasoline Model TMC Made): DIAGNOSIS SYSTEM

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the certification ECU (smart key ECU assembly), refer to Registration..

    Click here 2023 MY Corolla Corolla Hatchback GR Corolla [09/2022 - 11/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function (Gasoline Model, except TMMMS Made)): REGISTRATION

HINT:

  • Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
  • When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

PROCEDURE

1.

CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)

(a) Disconnect the cable from the negative (-) battery terminal.

(b) Disconnect the I167 certification ECU (smart key ECU assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I167-1 (CANH) - I167-2 (CANL)

Cable disconnected from negative (-) battery terminal

54 to 69 Ω

*a

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly))
NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
OK

2.

CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

I167-29 (E) - Body ground

Cable disconnected from negative (-) battery terminal

Below 1 Ω

*a

Front view of wire harness connector

(to Certification ECU (Smart Key ECU Assembly))

(b) Reconnect the cable to the negative (-) battery terminal.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

I167-6 (+B) - Body ground

Always

11 to 14 V
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)