Last Modified: 05-13-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026EDK |
Model Year Start: 2023 |
Model: GR Corolla |
Prod Date Range: [09/2022 -
] |
Title: MY SETTINGS: MY SETTINGS SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING; 2023 - 2025 MY Corolla Corolla Hatchback Corolla HV GR Corolla [09/2022 - ] |
HOW TO PROCEED WITH TROUBLESHOOTING
|
CAUTION / NOTICE / HINT
HINT:
-
Use the following procedure to troubleshoot the my settings system.
-
*: Use the GTS.
PROCEDURE
1.
|
VEHICLE BROUGHT TO WORKSHOP
|
NEXT
|
|
|
2.
|
CUSTOMER PROBLEM ANALYSIS AND SYMPTOM CHECK
|
NEXT
|
|
|
3.
|
READ AND SAVE VEHICLE CONTROL HISTORY (ROB)
|
NOTICE:
-
If the vehicle or vehicle controls are operated (for example, during initial inspection when the vehicle is brought in for repair) before vehicle control history (RoB) has been read and saved, the vehicle control history (RoB) information could be lost.
-
The vehicle control history (RoB) function uses the current system time of the GTS and the time counter inside the controlling ECU to calculate the times shown in the vehicle control history (RoB). For this reason, before reading the vehicle control history (RoB), first make sure that the GTS system clock is accurately set to the current time.
(a) Read and save vehicle control history (RoB) using the GTS.
Body Electrical > Main Body > Utility
Tester Display
|
Vehicle Control History (RoB)
|
NEXT
|
|
|
4.
|
INSPECT AUXILIARY BATTERY VOLTAGE
|
(a) Measure the auxiliary battery voltage with the ignition switch off.*1
(b) Measure the auxiliary battery voltage.*2
-
*1: for HV Model
-
*2: for Gasoline Model
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the auxiliary battery before proceeding to the next step.
NEXT
|
|
|
5.
|
CHECK CAN COMMUNICATION SYSTEM*
|
(a) Use the GTS to check if the CAN communication system is functioning normally.
for HV Model: Click here
for Gasoline Model: Click here
Result
|
Proceed to
|
CAN communication system DTCs are not output.
|
A
|
CAN communication system DTCs are output.
|
B
|
A
|
|
|
6.
|
CHECK SMART KEY SYSTEM (for Start Function)
|
(a) Check the smart key system (for Start Function).
for HV Model: Click here
for Gasoline Model: Click here
OK:
Smart key system (for Start Function) is normal
Result
|
Proceed to
|
OK (w/ Entry Function)
|
A
|
OK (w/o Entry Function)
|
B
|
NG
|
C
|
A
|
|
|
7.
|
CHECK SMART KEY SYSTEM (for Entry Function)
|
(a) Check the smart key system (for Entry Function).
Click here
OK:
Smart key system (for Entry Function) is normal
OK
|
|
|
8.
|
PROBLEM SYMPTOMS TABLE
|
(a) Refer to Problem Symptoms Table.
Click here
Result
|
Proceed to
|
Fault is not listed in Problem Symptoms Table (Fault can be simulated)
|
A
|
Fault is not listed in Problem Symptoms Table (Fault cannot be simulated)
|
B
|
Fault is listed in Problem Symptoms Table
|
C
|
A
|
|
|
9.
|
OVERALL ANALYSIS AND TROUBLESHOOTING*
|
(a) Data List / Active Test
Click here
NEXT
|
|
|
10.
|
ADJUST, REPAIR OR REPLACE
|
NEXT
|
|
|
NEXT |
|
END
|
|